Mitsubishi Colt Ralliart. Manual — part 421
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-192
COMMENTS ON TROUBLE SYMPTOM
If the room lamp do not illuminate, the wiring harness
connector(s), the bulb or the fuse may be defective
or burned out.
POSSIBLE CAUSES
• Malfunction of the room lamp
• Damaged harness wires and connectors
Step 1. Check that the luggage compartment
lamp illuminates.
Check that the luggage compartment lamp illumi-
nates normally.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Refer to Inspection Procedure M-1 "The
interior lamps (room ramp, luggage
compartment lamp) does not illuminate or
extinguish normally
Step 2. Connector check: C-04 room lamp
connector
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Repair the defective connector.
Step 3. Check the bulb.
Check whether the room lamp bulb is normal.
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Replace the bulb(s) of the defective lamp.
Step 4. Check the room lamp.
Check whether the room lamp is normal.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Replace the room lamp.
Step 5. Determine a trouble spot.
Q: Which switch position (DOOR or ON) does the
room lamp illuminate at?
The lamp illuminates at neither the ON or DOOR
position. :
Go to Step 6.
The lamp illuminates at the DOOR position. :
Go to
Step 7.
The lamp illuminates at the ON position. :
Go to
Step 9.
Step 6. Check the wiring harness from C-04 room
lamp connector terminal No.3 to fusible link (1).
AC401057
Connector: C-04
Harness side
AC
AC401058
Connectors: C-02, C-04
Harness side
AB
C-02
C-04
C-02
C-04
Main
Index
Group
TOC
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-193
NOTE:
Prior to the wiring harness inspection, check interme-
diate connector C-02 and junction block connector
B-108 and B-113 repair if necessary.
• Check the power supply line for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
).
NO :
Repair the wiring harness.
Step 7. Connector check: B-134 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Repair the defective connector.
Step 8. Check the wiring harness from B-134
ETACS-ECU connector terminal No.18 to C-04
room lamp connector terminal No.1
AC313825 AB
Connectors: B-108, B-113
Junction Block (Front view)
B-113
B-108 (B)
Harness side
B-108
Harness side
B-113
AC313826
Connector: B-134
AG
Junction block side
Junction block (Rear view)
AC313826
Connector: B-134
AG
Junction block side
Junction block (Rear view)
AC401058
Connectors: C-02, C-04
Harness side
AB
C-02
C-04
C-02
C-04
Main
Index
Group
TOC
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-194
NOTE:
Prior to the wiring harness inspection, check interme-
diate connector C-02 and junction block connector
B-113 repair if necessary.
• Check the input and output lines for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
).
NO :
Repair the wiring harness.
Step 9. Check the wiring harness from C-04 room
lamp connector terminal No.2 to body earth.
NOTE:
Prior to the wiring harness inspection, check interme-
diate connector C-02 and junction block connector
B-113 and B-130 repair if necessary.
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
).
NO :
Repair the wiring harness.
AC313824
Harness side
AB
Connector: B-113
Junction block (Front view)
AC401058
Connectors: C-02, C-04
Harness side
AB
C-02
C-04
C-02
C-04
AC313824
Harness side
AB
Connector: B-113
Junction block (Front view)
AC313826
Harness side
AE
Connector: B-130
Junction block (Rear view)
Main
Index
Group
TOC
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-195
INSPECTION PROCEDURE M-3: The luggage compartment lamp does not illuminate normally.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
ETACS-ECU
LUGGAGE
COMPARTMENT
LAMP
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
J/B SIDE
FUSIBLE
LINK
1
Luggage Room Lamp Circuit
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст