Mitsubishi Colt Ralliart. Manual — part 595
DOOR MIRROR
EXTERIOR
51-42
DOOR MIRROR
TROUBLESHOOTING
M1511020000412
The door mirror are controlled by the Smart Wiring
System (SWS). For troubleshooting, refer to GROUP
54B, troubleshooting
or GROUP 54C,
Troubleshooting
DOOR MIRROR
REMOVAL AND INSTALLATION
M1511006400654
AC403307
1
2
AD
5
4
3
4.9 ± 0.7 N·m
2
4
A
A
Section A – A
Claw
Remote controlled mirror switch
removal steps
•
Instrument panel under cover
(Refer to group 52A, Instrument
panel assembly
).
1.
Remote controlled mirror switch
Door mirror assembly removal
steps
2.
Door mirror base cover
3.
Door mirror assembly
4.
Door mirror
<<
A
>>
5.
Mirror
Main
Index
Group
TOC
DOOR MIRROR
EXTERIOR
51-43
REMOVAL SERVICE POINT
<<A>> MIRROR REMOVAL
CAUTION
The tab of the mirror is prone to breakage when
working in cold temperature. Always use a hair
drier or the like to warm up the mirror tab and its
periphery to 20
°C or higher prior to work. When
the mirror is heated too quickly from its cold
state, it may be broken.
AC207500
A
A
AD
Section A – A
Claw positions
Claws
Claw
Claw
Pivot plate
Recesses
Mirror
Mirror
Flat-tipped
screwdriver
Flat-tipped
screwdriver
Flat-tipped
screwdriver
Slant the mirror upward with your hands. Then insert
flat-tipped screwdriver wrapped with protective tape
between the pivot plate and mirror through the
cut-out from behind the mirror. Now pry off the mirror
tab and release the lower side of the mirror as shown
in the illustration.
INSPECTION
M1511019101548
DOOR MIRROR ASSEMBLY OPERATION
CHECK
Remove the door trim, and then connect the battery
to the door mirror assembly connector to check that
the door mirror operates.
AC313903
1 2 3 4 5 6 7
AB
Return
Retract
Forward-folding
Battery connection
Direction
operation
• Connect terminal 3 to the negative
battery terminal.
• Connect terminal 5 to the positive
battery terminal.
Up
• Connect terminal 3 to the positive
battery terminal.
• Connect terminal 5 to the negative
battery terminal.
Down
• Connect terminal 3 to the negative
battery terminal.
• Connect terminal 4 to the positive
battery terminal.
Right
• Connect terminal 3 to the positive
battery terminal.
• Connect terminal 4 to the negative
battery terminal.
Left
• Connect terminal 6 to the positive
battery terminal.
• Connect terminal 7 to the negative
battery terminal.
Retract
• Connect terminal 6 to the negative
battery terminal.
• Connect terminal 7 to the positive
battery terminal.
Return
Main
Index
Group
TOC
DOOR MIRROR
EXTERIOR
51-44
DOOR MIRROR CONTROL SWITCH CON-
TINUITY CHECK
AC208667
1 2
5 6 7 8 9 10 11
3 4
Switch position
Tester
connection
Specified
condition
OFF
1
− 2, 1 − 3, 1 − 4, 1
− 6, 1 − 10, 1 − 11,
2
− 9, 3 − 9, 6 − 9, 9
− 10, 9 − 11
Open circuit
Left side OFF
1
− 6, 1 − 10, 1 −
11, 6
− 9, 9 − 10, 9
− 11
Open circuit
Up
1
− 6, 9 − 11
Continuity
(Less than
2
Ω)
Down
1
− 11, 6 − 9
Right
1
− 6, 9 − 10
Left
1
− 10, 6 − 9
Right
side
OFF
1
− 2, 1 − 3, 1 − 6, 2
− 9, 3 − 9, 6 − 9
Open circuit
Up
1
− 6, 3 − 9
Continuity
(Less than
2
Ω)
Down
1
− 3, 6 − 9
Right
1
− 6, 2 − 9
Left
1
− 2, 6 − 9
Retract and return 1
− 4
Continuity
(Less than
2
Ω)
Main
Index
Group
TOC
GROUP 21A
CLUTCH
CONTENTS
GENERAL INFORMATION . . . . . . . .
SERVICE SPECIFICATIONS. . . . . . .
LUBRICANTS . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
CLUTCH PEDAL CHECK AND
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . .
CLUTCH BLEEDING . . . . . . . . . . . . . . . . .
CLUTCH PEDAL SWITCH CHECK AND
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . .
CLUTCH MONITOR SWITCH CHECK
AND ADJUSTMENT . . . . . . . . . . . . . . . . . .
CLUTCH PEDAL. . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
CLUTCH CONTROL . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст