Mitsubishi Colt Ralliart. Manual — part 10

AC405872AD

1

7

5

4

3

6

6

6

6

12 ± 2 N·m

7

8

9

10

11

11

2

12 ± 2 N·m

12 ± 2 N·m

9.0 ± 2.0 N·m

9.0 ± 2.0 N·m

9.0 ± 2.0 N·m

9.0 ± 2.0 N·m

13 ± 2 N·m

12 ± 2 N·m

12

Removal steps

>>

D

<<

•

Initialisation <Installation only>

1.

Brake booster vacuum hose
connection

2.

Transmission control cable
connection

3.

Earth connection

4.

Earth cable connection

5.

Fusible link box cover

6.

Control harness connection

7.

Engine-CVT-ECU mounting bolt
and nut

8.

Engine-CVT-ECU connector

9.

Purge solenoid hose connection

<<

A

>>

>>

C

<<

10. Fuel high-pressure hose

connection

11. Heater hose connection
12. Water hose connection

ENGINE ASSEMBLY

ENGINE MECHANICAL <4A9>

11A-37

Removal steps (Continued)

AC600593

AB

16

15

14

13

7.6 ± 0.6 N·m

17

63 ± 7 N·m

17

63 ± 7 N·m

68 ± 7 N·m

68 ± 7 N·m

18

18

19

20

18

N

49 ± 3 N·m

18*

18*

2

68 ± 7 N·m

NOTE
: Up to Feb. 2006 models
: From Mar. 2006 models

1

2

1

*

*

Removal steps

13. A/C compressor connector

<<

B

>>

14. A/C compressor and magnet clutch

assembly

15. Bell housing cover

<<

C

>>

16. Torque converter and drive plate

connecting bolt

•

Engine roll stopper rod assembly
(Refer to GROUP 32, Engine Roll
Stopper Rod Assembly

P.32-11

).

<<

D

>>

>>

B

<<

17. Transmission mounting insulator

connecting bolt and nut

<<

D

>>

>>

B

<<

18. Engine mounting insulator

connecting bolt and nut

<<

D

>>

>>

B

<<

19. Engine mounting insulator

<<

E

>>

>>

B

<<

20. Engine and transmission assembly

ENGINE ASSEMBLY

ENGINE MECHANICAL <4A9>

11A-38

Removal steps (Continued)

AC403076 AC

25

22

23

24 ± 3 N·m

24

23 ± 3 N·m

Inhibitor switch

21

N

Removal steps

21. Cable band
22. Control harness
23. Starter assembly

<<

F

>>

24. Transmission connecting bolt

<<

F

>>

>>

A

<<

25. Engine assembly

ENGINE ASSEMBLY

ENGINE MECHANICAL <4A9>

11A-39

Removal steps (Continued)

ENGINE ASSEMBLY

ENGINE MECHANICAL <4A9>

11A-40

REMOVAL SERVICE POINTS
<<A>> FUEL HIGH-PRESSURE HOSE
REMOVAL

AC403077AB

Fuel high-pressure
hose

Stopper

1. Remove the stopper.

AC403078 AB

Fuel high-pressure
hose

Retainer

2. Raise the retainer, and pull out the fuel

high-pressure hose.
NOTE: If the retainer comes off, install it securely
after pulling out the fuel high-pressure hose.

<<B>> A/C COMPRESSOR AND MAGNET
CLUTCH ASSEMBLY REMOVAL

1. With the hose installed, remove the A/C

compressor and magnet clutch assembly from the
cylinder block.

2. Secure the removed A/C compressor and magnet

clutch assembly with cord or rope at a position
where they will not interfere with the removal of
the engine and transmission assembly.

<<C>> TORQUE CONVERTER AND
DRIVE PLATE CONNECTING BOLT
REMOVAL

AC207401AB

Inhibitor switch

N position

Manual control
lever

1. Set the transmission in N (neutral) and remove

each coupling bolt while turning the crankshaft.
NOTE: The N (Neutral) state of the transmission
can be checked with the position of the manual
control lever.

2. Push in the torque converter into the transmission

side and make a point to ensure that the torque
converter does not remain on the engine side.