Mitsubishi Colt Ralliart. Manual — part 279
SUPPORT LOCATIONS FOR LIFTING AND JACKING
GENERAL
00-29
SUPPORT LOCATIONS FOR LIFTING AND JACKING
M1001000700190
SUPPORT POSITIONS FOR A GARAGE JACK, AXLE STANDS, SINGLE-POST LIFT OR
DOUBLE-POST LIFT AND PLATE TYPE LIFT
CAUTION
Do not support the vehicles at locations other than specified supporting points. Doing so will cause
damage, etc.
GARAGE JACK
CAUTION
• Use a low-profile type garage jack; otherwise use of conventional garage jack may cause interfer-
ence with bumper etc.
•
AC312331AB
Front axle No.1
crossmember
Front
Never support any point other than the specified one, or that point will be deformed.
Main
Index
Group
TOC
SUPPORT LOCATIONS FOR LIFTING AND JACKING
GENERAL
00-30
AXLE STANDS AND A SINGLE-POST LIFT OR DOUBLE-POST LIFT
CAUTION
• If rubber attachments with grooves that are too thick are used at the front support positions, the
front fender may become bent, so be sure to use rubber attachments with groove thickness of 18
mm or less.
• If attachments which are not high enough are used, they may damage areas such as the side step.
Be sure to use attachments which are high enough, or remove the side step if not using attach-
ments.
AC312300
AXLE STANDS
SINGLE-POST LIFT
OR DOUBLE-POST LIFT
Notch
Rubber
Rubber
AB
Front
Notch
Notch
Notch
Main
Index
Group
TOC
TOWING AND HOISTING
GENERAL
00-31
PLATE TYPE LIFT
CAUTION
To avoid damaging the side sill garnish, put a wooden block between the side sill and a lift.
Support the side sill flange with a lift.
TOWING AND HOISTING
M1001000800443
HOW TO ATTACH THE TOWING HOOK
When towing this vehicle, attach the towing hook
according to the procedure below.
AC207643AB
1. Withdraw the towing hook under the luggage floor
board in the luggage compartment.
AC209208
AB
Cap
2. Remove the cap on the right side of front bumper
by using a wheel nut socket wrench or a
flat-tipped screwdriver.
AC205837AB
3. Secure the towing hook.
Main
Index
Group
TOC
STANDARD PART/TIGHTENING-TORQUE TABLE
GENERAL
00-32
STANDARD PART/TIGHTENING-TORQUE TABLE
M1001001100500
Each torque value in the table is a standard value for
tightening under the following conditions.
1. Bolts, nuts and washers are all made of steel and
plated with zinc.
2. The threads and bearing surface of bolts and
nuts are all in dry condition.
The values in the table are not applicable:
1. If toothed washers are inserted.
2. If plastic parts are fastened.
3. If bolts are tightened to plastic or die-cast
inserted nuts.
4. If self-tapping screws or self-locking nuts are
used.
STANDARD BOLT AND NUT TIGHTENING TORQUE
Thread size
Torque N
⋅m
Bolt nominal
diameter mm
Pitch mm Head mark "4"
Head mark "7"
Head mark "8"
M5
0.8
2.5
± 0.5
5.0
± 1.0
6.0
± 1.0
M6
1.0
5.0
± 1.0
8.5
± 1.5
10
± 2
M8
1.25
11
± 2
20
± 4
24
± 4
M10
1.25
23
± 4
42
± 8
53
± 7
M12
1.25
42
± 8
80
± 10
93
± 12
M14
1.5
70
± 10
130
± 20
150
± 20
M16
1.5
105
± 15
195
± 25
230
± 30
M18
1.5
150
± 20
290
± 40
335
± 45
M20
1.5
210
± 30
400
± 60
465
± 65
M22
1.5
290
± 40
540
± 80
630
± 90
M24
1.5
375
± 55
705
± 105
820
± 120
FLANGE BOLT AND NUT TIGHTENING TORQUE
Thread size
Torque N
⋅m
Bolt nominal
diameter mm
Pitch mm Head mark "4"
Head mark "7"
Head mark "8"
M6
1.0
5.0
± 1.0
10
± 2
12
± 2
M8
1.25
13
± 2
24
± 4
28
± 5
M10
1.25
26
± 5
50
± 5
58
± 7
M10
1.5
25
± 4
46
± 8
55
± 5
M12
1.25
47
± 9
93
± 12
105
± 15
M12
1.75
43
± 8
83
± 12
98
± 12
NOTE:
.
•
Be sure to use only the specified bolts and nuts, and always tighten them to the specified torques.
•
Bolts marked with indications such as 4T or 7T are reinforced bolts. The larger the number, the greater the
bolt strength.
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст