Mitsubishi 380. Manual — part 516
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI)
13A-156
WARNING
If the air intake duct is removed from the throttle body take great care to keep fingers away
from the throttle plate. The drive motor has very high torque and is capable of random move-
ment at any time. Do not under any circumstances activate the throttly plate by hand.
When removing the throttle body from the intake manifold disconnect the wiring first. During
replacement connect the wiring last.
Do not activate the throttle body using a DC suppy to test the motor,as permanent damage to
the throttle body will result.
STEP 1. Using diagnostic tool , check data list item 13:
Throttle Position Sensor (main).
CAUTION
To prevent damage to diagnostic tool , always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting diagnostic tool .
(1) Connect diagnostic tool to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set diagnostic tool to the data reading mode for item 13,
Throttle Position Sensor (main).
(4) Apply the accelerator pedal as required to check the
following:
• Output voltage should be between 1035 and 1250 mV
when the throttle valve is fully close.
• Output voltage should be between 4000 and 4824 mV
when the throttle valve is fully open.
(5) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Go to Step 2.
STEP 2. Check harness connector B-06 at throttle position
sensor for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 8.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
03DB180A
CONNECTOR: B-06
B-06 (B)
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI)
13A-157
STEP 3. Check the continuity at throttle position sensor
harness side connector B-06.
(1) Disconnect the connector B-06 and measure at the harness
side.
(2) Measure the continuity between terminal No. 2 and ground
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 6.
NO : Go to Step 4.
STEP 4. Check harness connector B-20 at ENGINE-ECU for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 7.
03DB180A
CONNECTOR: B-06
B-06 (B)
03DB197A
THROTTLE ACTUATOR
CONTROL MOTOR
CONNECTOR
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI)
13A-158
STEP 5. Check for open circuit and harness damage
between throttle position sensor connector B-06 (terminal
No. 2) and ENGINE-ECU connector B-20 (terminal No. 27).
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair or replace it. Then go to Step 7.
STEP 6. Replace the throttle body assembly.
(1) Replace the throttle body assembly.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P0123 set?
YES : Then go to Step 7.
NO : The procedure is complete.
03DB180A
CONNECTOR: B-06
B-06 (B)
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
03DB180A
CONNECTOR: B-06
B-06 (B)
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI)
13A-159
STEP 7. Using diagnostic tool, read the diagnostic trouble
code (DTC).
CAUTION
To prevent damage to diagnostic tool, always turn the igni-
tion switch to the "LOCK"(OFF) position before connect-
ing or disconnecting diagnostic tool .
(1) Connect diagnostic tool to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P0123 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст