Mitsubishi 380. Manual — part 304
PARKING BRAKE LINING AND DRUM
PARKING BRAKES
36-8
PARKING BRAKE LINING AND DRUM
REMOVAL AND INSTALLATION
M1361002500315
Post-installation Operation
• Parking Brake Lever Stroke Check and Adjustment (Refer
to
).
• Parking Brake Lining Seating (Refer to
).
AC306238AB
6
13
13
BRAKE GREASE: BRAKE GREASE SAE J310, NLGI No.1
18
:
1
3
2
4
5
6
7
8
9
10
11
13
14
15
16
17
18
60 ± 5 N·m
45 ± 3 ft-lb
73 ± 7 N·m
54 ± 5 ft-lb
19
12
N
REMOVAL
STEPS
<<A>>
1.
REAR BRAKE BOLT
<<A>>
2.
REAR BRAKE CALIPER
ASSEMBLY
<<B>>
3.
REAR BRAKE DISC
4.
SHOE-TO-ANCHOR SPRING
5. ADJUSTING
WHEEL
SPRING
6.
REAR BRAKE SHOE SLACK
ADJUSTER
7.
PARKING BRAKE OPERATING
LEVER STRUT
8.
STRUT-TO- SHOE SPRING
9.
REAR BRAKE SHOE SPRING
CUP AND SHOE HOLD-DOWN
SPRING
10. PARKING BRAKE CABLE CLIP
11. REAR PARKING BRAKE CABLE
CONNECTION
12. O-RING
13. REAR BRAKE SHOE ASSEMBLY
<<C>> >>A<<
14. REAR BRAKE CHAMBER
RETAINER
15. REAR BRAKE WASHER
16. PARKING BRAKE OPERATING
LEVER
REMOVAL
STEPS
(Continued)
PARKING BRAKE LINING AND DRUM
PARKING BRAKES
36-9
REMOVAL SERVICE POINTS
.
<<A>> REAR BRAKE BOLT/REAR BRAKE CALI-
PER ASSEMBLY REMOVAL
Remove the rear brake caliper assembly and support it with
wire or something similar.
.
<<B>> REAR BRAKE DISC REMOVAL
If the rear brake disc is seized, install M8
×1.25 bolts as shown,
and remove the rear brake disc by tightening the bolts evenly
and gradually.
.
<<C>> REAR BRAKE CHAMBER RETAINER
REMOVAL
Use a flat-tipped screwdriver or a similar tool to open up the
rear brake chamber retainer joint. Then remove the rear brake
chamber retainer.
•
REAR WHEEL SPEED SENSOR
<VEHICLES WITH ABS> (REFER
TO GROUP 35B, WHEEL SPEED
SENSOR
).
17. REAR WHEEL HUB ASSEMBLY
18. BACKING PLATE
19. SHOE HOLD-DOWN PIN
REMOVAL
STEPS
(Continued)
AC205986
AB
BOLTS
(M8 × 1.25)
AC000924AD
PIN OF REAR BRAKE
SHOE ASSEMBLY
REAR BRAKE CHAMBER
RETAINER
PARKING BRAKE LINING AND DRUM
PARKING BRAKES
36-10
INSTALLATION SERVICE POINTS
.
>>A<< REAR BRAKE CHAMBER RETAINER
INSTALLATION
Use pliers or a similar tool to close the rear brake chamber
retainer end onto the pin.
.
>>B<< REAR BRAKE SHOE SLACK ADJUSTER
INSTALLATION
Install the rear brake shoe slack adjuster as shown.
.
AC000926AF
PIN OF REAR BRAKE
SHOE ASSEMBLY
REAR BRAKE CHAMBER
RETAINER
AC206987
AB
REAR BRAKE SHOE
SLACK ADJUSTER
REAR
LEFT SIDE WHEEL
AC206987
AC
REAR BRAKE SHOE
SLACK ADJUSTER
FRONT
RIGHT SIDE WHEEL
PARKING BRAKE LINING AND DRUM
PARKING BRAKES
36-11
>>C<< SHOE-TO-ANCHOR SPRING
INSTALLATION
CAUTION
The front and rear shoe-to-anchor springs are not inter-
changeable, so the blue spring must be installed at the
front side and the yellow spring must be installed at the
rear side.
Install the shoe-to-anchor springs in the order shown in the
illustration.
INSPECTION
M1361002600260
PARKING BRAKE LINING AND BRAKE DRUM
CHECK
1. Measure the thickness of the brake lining at several places.
Standard value: 2.8 mm (0.11 inch)
Minimum Limit: 1.0 mm (0.04 inch)
2. If the thickness of the brake lining is below the limit, replace
the shoe assemblies on both sides of the vehicle. Never
replace only one side.
3. Measure the inside diameter of the brake disc in two places
or more.
Standard value: 190.0 mm
Limit: 191.0 mm
4. If the inside diameter exceeds the limit, or if it is excessively
worn on one side, replace the brake disc.
AC206986
AB
REAR
1 (BLUE SPRING)
2 (YELLOW SPRING)
LEFT SIDE WHEEL
AC209387
AB
REAR
1 (BLUE SPRING)
2 (YELLOW SPRING)
RIGHT SIDE WHEEL
ACX00708AB
ACX00709AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст