Mitsubishi 380. Manual — part 430
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-260
STEP 12. Check the shift switch assembly.
Refer to
, Transmission Control.
Q: Is the switch operating properly?
YES : Go to Step 13.
NO : Replace the shift switch assembly. Refer to
, Transmission Control.
STEP 13. Measure the switch output voltage at A/T-ECU
connector B-19 by using check harness special tool
MB992045.
(1) Disconnect all the connectors from the A/T-ECU.
(2) Connect special tool MB992045 (check harness) between
the A/T-ECU and the body-side harness connector.
(3) Turn the ignition switch to the "ON" position.
(4) Move the selector lever to the sport mode.
(5) Measure the voltage between connector B-19 terminal 17
and ground.
• The voltage should measure battery positive voltage.
(6) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 16.
NO : Go to Step 14.
10DB125A
COVER
AIR
CLEANER
A/T
CONTROL
UNIT
CONNECTOR: B-19
10DB161A
A/T-ECU CHECK HARNESS
MB992045
A/T-ECU
A/T-ECU CHECK
HARNESS
CONNECTORS
10DB128A
B-19 HARNESS
CONNECTOR:
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-261
STEP 14. Check A/T-ECU connector B-19 and shift switch
assembly connector D-14 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 15.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
10DB125A
COVER
AIR
CLEANER
A/T
CONTROL
UNIT
CONNECTOR: B-19
10DB093A
CONNECTOR: D-14
FLOOR
WIRING
HARNESS
4
Y
2
15
ROOF
WIRING
HARNESS
D-14
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-262
STEP 15. Check the harness for open circuit or short
circuit to ground between A/T-ECU connector B-19
terminal 17 and shift switch assembly connector D-14
terminal 6.
Q: Is the harness wire in good condition?
YES : Go to Step 4.
NO : Repair or replace the harness wire.
STEP 16. Check A/T-ECU connector B-19 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 4.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
10DB125A
COVER
AIR
CLEANER
A/T
CONTROL
UNIT
CONNECTOR: B-19
10DB093A
CONNECTOR: D-14
FLOOR
WIRING
HARNESS
4
Y
2
15
ROOF
WIRING
HARNESS
D-14
16DB564A
COVER
AIR
CLEANER
A/T
CONTROL
UNIT
CONNECTORS: B-19, B-22
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-263
STEP 17. Check the shift switch assembly.
Refer to
, Transmission Control.
Q: Is the switch operating properly?
YES : Go to Step 18.
NO : Replace the shift switch assembly. Refer to
, Transmission Control.
STEP 18. Measure the switch output voltage at A/T-ECU
connector B-19 by using check harness special tool
MB992045.
(1) Disconnect all the connectors from the A/T-ECU.
(2) Connect special tool MB992045 (check harness) between
the A/T-ECU and the body-side harness connector.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between connector B-19 terminal 8
and ground.
• The voltage should measure battery positive voltage
when the selector lever is upshift and hold.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 21.
NO : Go to Step 19.
16DB564A
COVER
AIR
CLEANER
A/T
CONTROL
UNIT
CONNECTORS: B-19, B-22
10DB161A
A/T-ECU CHECK HARNESS
MB992045
A/T-ECU
A/T-ECU CHECK
HARNESS
CONNECTORS
10DB129A
B-19 HARNESS
CONNECTOR:
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст