Mitsubishi 380. Manual — part 625
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI) <3.8L ENGINE>
13A-592
STEP 3. Check the advance ignition timing.
Ignition timing is controlled by the ENGIN-ECUand will vary
depending on engine requirement..
Q: Is the advance ignition timing normal?
YES : Go to Step 4.
NO : Check that the crankshaft position sensor and timing
belt cover are in the correct position. Then confirm
that the malfunction symptom is eliminated.
STEP 4. Using diagnostic tool, check data list.
CAUTION
To prevent damage to diagnostic tool, always turn the igni-
tion switch to the "LOCK" (OFF) position before connect-
ing or disconnecting diagnostic tool.
(1) Connect diagnostic tool to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check the following items in the data list. Refer to Data List
.
a. Item 5: Intake Air Temperature Sensor.
b. Item 6: Engine Coolant Temperature Sensor.
c. Item AD: Right Bank Heated Oxygen Sensor (rear).
d. Item AC: Right Bank Heated Oxygen Sensor (front).
e. Item AF: Left Bank Heated Oxygen Sensor (rear).
f. Item AE: Left Bank Heated Oxygen Sensor (front).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are they operating properly?
YES : Go to Step 5.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI) <3.8L ENGINE>
13A-593
STEP 5. Using diagnostic tool, check data list.
(1) Turn the ignition switch to the "ON" position.
(2) Check the following items of data list. Refer to Data List
.
a. Item AC: Right Bank Heated Oxygen Sensor (front).
b. Item AE: Left Bank Heated Oxygen Sensor (front).
• Voltage should fluctuate between 0 − 0.4 volt and 0.6 −
1.0 volt while idling after the engine has been warmed.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are they operating properly?
YES : Go to Step 7.
NO : Go to Step 6.
STEP 6. Check the fuel pressure.
Refer to On-vehicle Service
− Fuel Pressure Test
Q: Is the fuel pressure normal?
YES : Check the following items, and repair or replace the
defective items.
a. Vacuum leak.
• Broken intake manifold gasket.
• Broken air intake hose.
• Broken vacuum hose.
• Positive crankcase ventilation valve does
not operate.
b. Injector clogged.
Then confirm that the malfunction symptom is
eliminated.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI) <3.8L ENGINE>
13A-594
STEP 7. Check the fuel pressure.
Refer to On-vehicle Service
− Fuel Pressure Test
Q: Is the fuel pressure normal?
YES : Check the following items, and repair or replace the
defective items.
a. Check the ignition coil and spark plugs.
b. Check compression pressure.
c. Check the fuel filter or fuel line for clogging.
d. Broken air intake hose.
e. Clogged air cleaner.
f. Clogged exhaust system.
Then confirm that the malfunction symptom is
eliminated.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
INSPECTION PROCEDURE 19: Surge.
.
COMMENT
• Defective ignition system, abnormal air/fuel ratio,
the electronic control throttle valve system failed,
etc. are suspected.
.
TROUBLESHOOTING HINTS (The most
likely causes for this case:)
• Malfunction of the ignition system.
• Malfunction of air/fuel ratio control system.
• Malfunction of the electronic control throttle valve
system.
• Refer to component locations GROUP-
• Refer to configuration diagrams GROUP-
• Refer to circuit diagrams GROUP-
DIAGNOSIS
Required Special Tools:
• Diagnostic tool(MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI) <3.8L ENGINE>
13A-595
STEP 1. Using diagnostic tool, read the diagnostic trouble
code (DTC).
CAUTION
To prevent damage to diagnostic tool, always turn the igni-
tion switch to the "LOCK" (OFF) position before connect-
ing or disconnecting diagnostic tool.
(1) Connect diagnostic tool to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the DTC.
(4) Turn the ignition switch to the "ON" position.
Q: Is the DTC set?
YES : Refer to Diagnostic Trouble Code Chart
.
NO : Go to Step 2.
STEP 2. Using diagnostic tool, check actuator test items
01, 02, 03, 04, 05, 06: Injector.
(1) Turn the ignition switch to the "ON" position.
(2) Check following items in the actuator test. Refer to Actuator
Test Reference Table
.
a. Item 01, 02, 03, 04, 05, 06: Injector.
(3) Turn the ignition switch to the "ON" position.
Q: Are thy operating properly?
YES : Go to Step 3.
NO : Refer to DTC P0201
,
,
− Injector Circuit.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст