Mitsubishi 380. Manual — part 626
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI) <3.8L ENGINE>
13A-596
STEP 3. Check the advance ignition timing.
Ignition timing is controlled by the ENGIN-ECUand will vary
depending on engine requirement..
Q: Is the advance ignition timing normal?
YES : Go to Step 4.
NO : Check that the crankshaft position sensor and timing
belt cover are in the correct position. Then confirm
that the malfunction symptom is eliminated.
STEP 4. Using diagnostic tool, check data list.
CAUTION
To prevent damage to diagnostic tool, always turn the igni-
tion switch to the "LOCK" (OFF) position before connect-
ing or disconnecting diagnostic tool.
(1) Connect diagnostic tool to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check the following items in the data list. Refer to Data List
.
a. Item 05: Intake Air Temperature Sensor.
b. Item 06: Engine Coolant Temperature Sensor.
c. Item AD: Right Bank Heated Oxygen Sensor (rear).
d. Item AC: Right Bank Heated Oxygen Sensor (front).
e. Item AF: Left Bank Heated Oxygen Sensor (rear).
f. Item AE: Left Bank Heated Oxygen Sensor (front).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are they operating properly?
YES : Go to Step 5.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI) <3.8L ENGINE>
13A-597
STEP 5. Using diagnostic tool, check data list.
(1) Turn the ignition switch to the "ON" position.
(2) Check the following items of data list. Refer to Data List
.
a. Item AC: Right Bank Heated Oxygen Sensor (front).
b. Item AE: Left Bank Heated Oxygen Sensor (front).
• Voltage should fluctuate between 0 − 0.4 volt and 0.6 −
1.0 volt while idling after the engine has been warmed.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are they operating properly?
YES : Go to Step 7.
NO : Go to Step 6.
STEP 6. Check the fuel pressure.
Refer to On-vehicle Service
− Fuel Pressure Test
Q: Is the fuel pressure normal?
YES : Check the following items, and repair or replace the
defective items.
a. Vacuum leak.
• Broken intake manifold gasket.
• Broken air intake hose.
• Broken vacuum hose.
• Positive crankcase ventilation valve does
not operate.
b. Injector clogged.
Then confirm that the malfunction symptom is
eliminated.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
STEP 7. Check the fuel pressure.
Refer to On-vehicle Service
− Fuel Pressure Test
Q: Is the fuel pressure normal?
YES : Check the following items, and repair or replace the
defective items.
a. Check the ignition coil and spark plugs.
Then confirm that the malfunction symptom is
eliminated.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI) <3.8L ENGINE>
13A-598
INSPECTION PROCEDURE 20: Knocking
.
COMMENT
• Incase such as the above, the cause is probably
that the detonation control is defective or the heat
value of the spark plug is inappropriate.
.
TROUBLESHOOTING HINTS (The most
likely causes for this case:)
• Defective knock sensor.
• Incorrect heat value of the spark plug.
• Refer to component locations GROUP-
• Refer to configuration diagrams GROUP-
• Refer to circuit diagrams GROUP-
DIAGNOSIS
Required Special Tools:
• Diagnostic tool(MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Using the diagnostic tool, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to diagnostic tool, always turn the igni-
tion switch to the "LOCK" (OFF) position before connect-
ing or disconnecting diagnostic tool.
(1) Connect diagnostic tool to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the DTC.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Refer to Diagnostic Trouble Code Chart
.
NO : Go to Step 2.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI) <3.8L ENGINE>
13A-599
STEP 2. Check Data list, Item No. 16 advance ignition
timing.
(1) The advance ignition timing should retard more when knock
sensor connector B-120 is disconnected than when it is
connected.
Q: When the knock sensor connector B-120 was
disconnected, was the advance ignition timing delayed?
YES : Check the following items, and repair or replace the
defective items.
a. Check the spark plugs.
b. Fuel quality, octane level.
c. Check if the foreign materials (water,
kerosene, etc.) got into fuel.
Then confirm that the malfunction symptom is
eliminated.
NO : Refer to DTC P0325
− Knock Sensor Circuit
.
INSPECTION PROCEDURE 21: Dieseling (Run-on).
.
COMMENT
• Fuel leakage from injectors is suspected, or car-
bon build up.
.
TROUBLESHOOTING HINTS (The most
likely causes for this case:)
• Fuel leakage from injectors.
DIAGNOSIS
Replace the leaking injector. Then confirm that the malfunction
symptom is eliminated.
AK303120
1
2
KNOCK SENSOR
AB
CONNECTOR: B-120
B-120 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст