Mitsubishi 380. Manual — part 133
FRONT SEAT ASSEMBLY
INTERIOR
52A-40
LHS: 380GT (leather)
19DB014A
17
18
15
15
13
22
21
20
3
5
4
6
7
23
24
2
1
10
11
12
14
8
9
35 N·m
35 N·m
45 N·m
5 N·m
19
32 N·m
FRONT SEAT ASSEMBLY
INTERIOR
52A-41
REMOVAL STEPS
<<A>>
HEADREST
1.
HINGE COVER
2.
INNER SEAT BELT
3.
MANUAL RECLINER ADJUSTER
HANDLE (VEHICLES WITH
MANUAL RECLINER)
4.
SIDE SHIELD COVER
5.
FORE AFT ADJUSTER KNOB
6.
MAIN POWER SWITCH
7.
SIDE SHIELD MOUNT BRACKET
8.
FRONT SEAT BACK ASSEMBLY
9.
CUSHION ASSEMBLY
10. SEAT CUSHION COVER
11. SEAT CUSHION PAD
12. SEAT CUSHION FRAME
13. SEATBACK PANEL
14. SIDE AIRBAG MODULE
<<B>>
15. HEADREST GUIDE
16
MANUAL LUMBAR ADJUSTER
HANDLE
<<C>>
17. SEATBACK COVER
18. SEATBACK PAD
19. LUMBAR ASSEMBLY
20. RECLINER LEVER RETURN
SPRING
21. RECLINER LEVER SHAFT
22. SEAT BACK FRAME
23. SEAT POWER HARNESS
24. SEAT SLIDE ADJUSTER
REMOVAL STEPS (Continued)
FRONT SEAT ASSEMBLY
INTERIOR
52A-42
REMOVAL SERVICE POINT
.
<<A>> HEADREST REMOVAL
1. Raise the head restraint fully.
2. Insert a probe that is suited to fit into the hole (1) in the right
hand head restraint sleeve (2) as illustrated in the figure
below.
3. Whilst the probe is inserted slightly, apply slight pressure on
the head restraint. Apply and hold pressure upwards.
4. To remove the head restraint, you must depress the sleeve
height adjuster lock (3) on the left-hand head restraint
sleeve as illustrated below.
<<B>> HEADREST SLEEVE REMOVAL
1. To reveal upper portion of the seat back frame or
active head restraint frame (1) as shown in figure
below, push down on the surrounding seat cover.
2. By using a small flat blade screwdriver, depress
the sleeve locking tab (2), and remove the head
restaint sleeve (3) in upwards movement from the
frame as illustrated below.
3. If required, repeat process for the remaining
sleeve.
<<C>> SEAT BACK PANEL REMOVAL
AND FITMENT
1. Move front seat to the most forward position.
2. Pull the lower edge of seat panel towards you, as
shown below (1).
3. Slide the panel downwards (2) as the top section
is held in by 2 locating hooks (lugs).
4. Upon fitment, be sure to firstly locate the top 2
lugs into position (2), as shown above.
5. Approximately square up panel to the seat, so by
doing this you will be able to locate the bottom 2
clips to press in the panel (1), as shown above.
19DB015A
19DB016A
19DB017A
HOOK
(LUG)
FRONT
SEATBACK
ASSEMBLY
ATTACHMENT
LOCATION
SEAT BACK
PANEL
(1) Pull bottom side
panel out
(2) Slide panel
downwards
CLIP
FRONT SEAT TRIM COVER
INTERIOR
52A-43
FRONT SEAT TRIM COVER
REMOVAL AND FITMENT
REMOVAL
.
1. Remove seat from vehicle and cushion or seat back
assembly as required. Remove all seat plastic covers etc.
2. Unclip all the plastic retainer clips at the rear of the trim
cover. This is typical for the cushion and the back of the
seat.
3. Peel cover away from the foam pad.
NOTE: Place a finger on the Blue Velcro strip when peeling
the cover to prevent the strip being pulled out of the foam
pad.
19DB031A
CLIPS LOCATED UNDERNEATH SEAT
19DB026A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст