Mitsubishi 380. Manual — part 403
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-152
STEP 12. Check the harness for an open or short circuit to
ground between A/T-ECU connector B-22 (terminals 1, 14
and 2) and A/T control solenoid valve assembly connector
B-108 (terminals 3, 4 and 5).
Q: Are the harness wires in good condition?
YES : Go to Step 13.
NO : Repair or replace the harness wire.
16DB564A
COVER
AIR
CLEANER
A/T
CONTROL
UNIT
CONNECTORS: B-19, B-22
AC306322
CONNECTOR: B-108
B-108 (GR)
AC
TRANSMISSION
RANGE SWITCH
2
7
1
8
3
9
4
6
10
5
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-153
STEP 13. Check the harness for an open or short circuit to
ground between A/T control solenoid valve assembly
connector B-108 (terminals 3, 4, 5, and 9) and solenoid
valve connectors B-108-1, B-108-2 and B-108-3.
Q: Is the harness wire in good condition?
YES : Replace the A/T-ECU.
NO : Replace the harness wire.
AC306322
CONNECTOR: B-108
B-108 (GR)
AC
TRANSMISSION
RANGE SWITCH
2
7
1
8
3
9
4
6
10
5
VALVE BODY
ASSEMBLY
10DB106A
CONNECTORS: B-108-1, B-108-2, B-108-3
B-108-1
B-108-2
B-108-3
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-154
(P0763): Second Solenoid Valve System
.
SOLENOID VALVE SYSTEM CIRCUIT
Refer to
.
.
CIRCUIT OPERATION
Refer to
.
.
DTC SET CONDITIONS
Check Conditions
• Solenoid status: either solid ON or OFF.
• Shift status: in-gear.
• Voltage of battery: 10 volts or more.
Judgement Criteria
• Solenoid voltage: 3 volts or less. (0.3 second)
• If (P0763) is set consecutively four times, the
transmission is locked into 3rd gear as a fail-safe
measure, and the "N" range light flashes once
per second.
.
OBD-II DRIVE CYCLE PATTERN
Start the engine, and keep the vehicle stopped in "P"
range for 5 seconds.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CODE TO BE
SET ARE:)
• Malfunction of the second solenoid valve
• Damaged harness or connector
• Malfunction of the A/T-ECU
Circuit drawings
• Refer to circuit diagrams GROUP-
• Refer to configuration diagrams GROUP-
• Refer to component locations GROUP-
DIAGNOSIS
Required Special Tool:
• MB991958: Diagnostic Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
STEP 1. Using diagnostic tool MB991958, check actuator
test item 03: Second Solenoid Valve.
CAUTION
To prevent damage to diagnostic tool MB991958, always
turn the ignition switch to the "LOCK" (OFF) position
before connecting or disconnecting diagnostic tool
MB991958.
(1) Connect diagnostic tool MB991958 to the data link
connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set diagnostic tool MB991958 to the actuator test mode.
• Item 03: Second Solenoid Valve.
• An audible clicking or buzzing should be heard when
the second solenoid valve is energized.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the solenoid valve operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Go to Step 2.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-155
STEP 2. Using diagnostic tool MB991958, read the A/T
diagnostic trouble code.
(1) Connect diagnostic tool MB991958 to the data link
connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for A/T diagnostic trouble code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is (P1751) set? (P1751 may be set along with multiple
(P1751): A/T Control Relay
System.
NO : Go to Step 3.
STEP 3. Using diagnostic tool MB991958, read the A/T
diagnostic trouble code.
(1) Connect diagnostic tool MB991958 to the data link
connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for A/T diagnostic trouble code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are (P0758) and (P0768) set? (Multiple DTCs may be
set).
YES : Go to Step 8.
NO : Go to Step 4.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст