Mitsubishi 380. Manual — part 121
CHECK AT ECU TERMINAL
SIMPLIFIED WIRING SYSTEM (SWS)
54B-481
22
Output to door unlock (for
driver's door)
When driver's door lock actuator
is operating (doors unlocked)
Battery positive voltage
23, 24
−
−
−
25
Input of door lock key cylinder
switch (UNLOCK) signal
Door lock key cylinder switch:
UNLOCK
0 V
26
− 28
−
−
−
29
Input of rear door lock actuator
(UNLOCK) signal
Rear door lock actuator:
UNLOCK
0 V
30
Input of key reminder switch
signal
Key reminder switch: ON (when
ignition key is removed)
0 V
31, 32
−
−
−
33
Input of door lock switch (LOCK)
signal
Door lock switch (incorporated in
power window switch): LOCK
0 V
34
Input of door lock switch
(UNLOCK) signal
Door lock switch (incorporated in
power window switch): UNLOCK
0 V
35
Input from rear door switch (RH) Rear door switch (RH): ON (rear
door (RH) open)
0 V
36
Input of driver's door lock
actuator (UNLOCK) signal
Driver's door lock actuator:
UNLOCK
0 V
37
Input from trunk lid latch
assembly
Trunk lid latch: ON (trunk open)
0 V
38
Ground (for sensor)
Always
0 V
39
− 41
−
−
−
42
Input of door lock key cylinder
switch (LOCK) signal
Door lock key cylinder switch:
LOCK
0 V
43
Input of front passenger's door
lock actuator (UNLOCK) signal
Front passenger’s door lock
actuator: UNLOCK
0 V
44
Output to horn relay
When a horn sounds by the
keyless entry horn answerback
function
2 V or less
45
Output to data link connector
When DTC sets
0
− 12 V (pulse signal)
When input check signal is
output
0
− 12 V (when input
pulse signal is
fluctuating)
46
Output to trunk lamp
When trunk lid latch on.
0 V
47
−
−
−
48
Input of fog lamp switch signal
Fog lamp switch: ON
0 V
49
Input of hazard warning lamp
switch signal
Hazard warning lamp switch: ON
(When the switch is depressed)
0 V
50
Ground (for sensor)
Always
0 V
51
Key Ring Antenna (+)
0 V
0 V
52
Key Ring Antenna (-)
0 V
0 V
53
SWS communication line
Always
0
− 12 V (pulse signal)
TERMINAL
NO.
INSPECTION ITEM
INSPECTION CONDITION
NORMAL VALUE
CHECK AT ECU TERMINAL
SIMPLIFIED WIRING SYSTEM (SWS)
54B-482
54
− 58
−
−
−
59
Input from front passenger's door
switch
Front passenger's door switch:
ON (front passenger's door
open)
0 V
60
Input of signal from variable
intermittent wiper control switch
Ignition switch: "ACC,"
Variable intermittent wiper
control switch: "FAST" to
"SLOW"
0
→ 2.5 V
61
Input of diagnosis indication
selection
When diagnostic tool is
connected
0 V
62
Output of data request signal
Always
0
− 12 V (pulse signal)
63
Output to ignition key hole
illumination lamp
When ignition key hole
illumination lamp is on
0 V
64
− 65
−
−
−
66
CAN HI
Always
60
± 10 Ω
67
CAN LO
Always
60
± 10 Ω
68
Output to security lamp
−
0 V
TERMINAL
NO.
INSPECTION ITEM
INSPECTION CONDITION
NORMAL VALUE
CHECK AT ECU TERMINAL
SIMPLIFIED WIRING SYSTEM (SWS)
54B-483
COLUMN SWITCH
5
4
3
2
1
10
9
8
7
6
ACX01512
C-309
AB
TERMINAL
NO.
INSPECTION ITEM
INSPECTION CONDITION
NORMAL VALUE
1
Battery power supply
Always
Battery positive voltage
2
Input of data request signal
Always
0
− 12 V (pulse signal)
3
SWS communication line
Always
0
− 12 V (pulse signal)
4
Ground
Always
0 V
5
−
−
−
6
Output of signal from variable
intermittent wiper control switch:
"FAST" to "SLOW"
Igniting switch: "ACC,"
Variable intermittent wiper
control switch: "FAST" to
"SLOW"
0
→ 2.5 V
7
−
−
−
8
Output of backup signal from
windshield wiper switch
Windshield low-speed wiper
switch or windshield high-speed
wiper switch: ON
0 V
9
Power supply to ignition switch
(IG1)
Ignition switch: "ON"
Battery positive voltage
10
Output of backup signal from
headlamp switch
Ignition switch: "ON,"
Headlamp switch: ON
0 V
CHECK AT ECU TERMINAL
SIMPLIFIED WIRING SYSTEM (SWS)
54B-484
FRONT-ECU
NOTE: Terminal voltages cannot be measured as the
front-ECU is installed directly on the relay box.
Therefore, this information is only for reference.
1
3
2
4
10
7
5 6
8 9
11
2122
25
2324
2627
30
2829
31
AC210659
A-11X
A-12X
AB
TERMINAL
NO.
INSPECTION ITEM
INSPECTION CONDITION
NORMAL VALUE
1
Output to fog lamp relay
When the fog lamps are on
Battery positive voltage
2
Output to headlamp (high-beam) When headlights (high-beam)
are on
Battery positive voltage
3, 4
Battery power supply (for
headlamp)
Always
Battery positive voltage
5
Battery power supply (for
taillamp)
Always
Battery positive voltage
6
Output to headlamp (low-beam)
When headlights (low-beam) are
on
Battery positive voltage
7
Battery power supply (for ECU)
Always
Battery positive voltage
8
Output to taillamps
When taillamps are on
Battery positive voltage
9
− 11
−
−
−
21
Output to windshield washer
When windshield washer is on
Battery positive voltage
22
SWS communication line
Always
0
− 12 V (pulse signal)
23
Input of automatic stop signal to
windshield wiper
When windshield wiper is on
Battery positive voltage
24
Power supply to ignition switch
(ACC)
Ignition switch: "ACC"
Battery positive voltage
25
Input of backup signal from
headlamp switch
Headlamp switch: ON
0 V
26
Input of backup signal to
windshield wiper
Windshield low-speed wiper
switch or windshield high-speed
wiper switch: ON
0 V
27
Output to windshield wiper
(low-speed)
When windshield wiper is on (at
low speed)
Battery positive voltage
28
Output to windshield wiper
(high-speed)
When windshield wiper is on (at
high speed)
Battery positive voltage
30
Power supply to ignition switch
(IG2)
Ignition switch: "ON"
Battery positive voltage
31
Ground
Always
0 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст