Mitsubishi Outlander (2003+). Manual — part 320
KEYLESS ENTRY SYSTEM
BODY
42-55
When the MUT-II is used
1. Check that the doors lock normally when the key
is used.
2. Insert the ignition key.
CAUTION
Before connecting or disconnecting the MUT-II,
turn the ignition switch to the "LOCK" (OFF)
position.
3. Connect the MUT-II to the diagnosis connector.
4. Press the hazard warning switch six times within
10 seconds.
NOTE: Once the process is completed six times,
then it will operate with all doors and tailgate lock
and unlock operations once and then go to the
save mode.
NOTE: The hazard warning lamp switch is turned
on and off alternately whenever it is pushed.
5. Press the transmitter switch, and then press it two
times within 10 seconds of the first press. This will
register the code.
6. Once the program is saved, it will operate once
with the all doors and tailgate lock and unlock
operations.
7. If you are using two or more transmitters or have
added a second transmitter, the same registration
procedure should be carried out within one minute
after registering the code for the first transmitter.
8. Registration mode will be canceled under the
following conditions:
•
When the secret code for four transmitters has
been registered;
•
When one minute has passed after registration
mode started;
•
When the MUT-II is disconnected from the
diagnosis connector
•
When the key is removed from the key cylinder;
9. After the registration is completed, remove the
ignition key and close all the doors, and then
check that the keyless entry system operates
normally.
When the special tool V. C. I. MB991824 is
used
1. Check that the doors lock normally when the key
is used.
2. Insert the ignition key.
CAUTION
Before connecting or disconnecting the V. C. I.,
turn the ignition switch to the "LOCK" (OFF)
position.
3. Connect the V. C. I. to the diagnosis connector.
AC107200AC
MB991502
16 Pin
ACX00571
MUT-II connected
Within 10 seconds
Hazard
warning
switch
ON
OFF
1
2
3
4
5
6
AB
AC305321
AC
MB991911
MB991824
16-Pin
KEYLESS ENTRY SYSTEM
BODY
42-56
4. Within 10 seconds after turning the V.C.I. power
switch to the "ON" position, press the hazard
switch six times.
NOTE: Once the process is completed six times,
then it will operate with all doors and tailgate lock
and unlock operations once and then go to the
save mode.
NOTE: The hazard warning lamp switch is turned
on and off alternately whenever it is pushed.
5. Press the transmitter switch, and then press it two
times within 10 seconds of the first press. This will
register the code.
6. Once the program is saved, it will operate once
with the all doors and tailgate lock and unlock
operations.
7. If you are using two or more transmitters or have
added a second transmitter, the same registration
procedure should be carried out within one minute
after registering the code for the first transmitter.
8. Registration mode will be canceled under the
following conditions:
•
When the secret code for four transmitters has
been registered;
•
When one minute has passed after registration
mode started;
•
When the V. C. I. is disconnected from the
diagnosis connector;
•
When the key is removed from the key cylinder;
9. After the registration is completed, remove the
ignition key and close all the doors, and then
check that the keyless entry system operates
normally.
ACX00571
Connect V. C. I. and turn
the V. C. I. power supply
switch ON.
Within 10 seconds
Hazard
warning
switch
ON
OFF
1
2
3
4
5
6
AJ
SUNROOF ASSEMBLY
BODY
42-57
SUNROOF ASSEMBLY
SERVICE SPECIFICATIONS
M1421000300255
TROUBLESHOOTING
CHECK CHART FOR TROUBLE
SYMPTOMS
M1426002000114
Item
Standard value
Roof lid glass operation current A (at 20
°
C)
7 or less
Symptom
Inspection
procedure
number
Reference
page
Sunroof does not work at all.
1
Any of the sunroof switch positions is defective.
2
Sunroof anti-trap function does not work normally.
3
SUNROOF ASSEMBLY
BODY
42-58
INSPECTION PROCEDURE 1: The sunroof does not work at all.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
CONTROL CIRCUIT
SUNROOF
SWITCH
SUNROOF
MOTOR ASSEMBLY
FUSIBLE
LINK
5
IGNITION
SWITCH (IG2)
Wire colour code
B : Black LG : Light green G : Green L : Blue
W : White Y : Yellow SB : Sky blue BR : Brown
O : Orange GR : Gray R : Red P : Pink V : Violet
AC309237AB
Sunroof-ECU Power Supply Circuit <L.H. drive vehicles>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст