Mitsubishi Outlander (2003+). Manual — part 318
TAILGATE
BODY
42-47
TAILGATE HANDLE AND LATCH
REMOVAL AND INSTALLATION
M1424001700147
Pre-removal Operation
•
Tailgate Handle Play Check (Refer to
).
AC102861
1
2
3
4
5
6
7
6
4
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
22 ± 4 N·m
9.0 ± 2.0 N·m
AC
Striker removal steps
•
Rear end trim (Refer to GROUP 52A,
Trims
).
>>A<<
1. Striker
Tailgate handle and lock key cylinder
removal steps
•
Lower tailgate trim (Refer to GROUP
52A, Tailgate Trim
•
Waterproof film (Refer to
).
2. Tailgate Lock Actuator Connection
3. Tailgate lock key cylinder
4. Tailgate handle
Tailgate latch removal steps
•
Lower tailgate trim (Refer to GROUP
52A, Tailgate Trim
•
Waterproof film (Refer to
5. Bolt (earth)
6. Tailgate latch assembly
Tailgate lock actuator removal steps
•
Lower tailgate trim (Refer to GROUP
52A, Tailgate Trim
•
Waterproof film (Refer to
7. Tailgate lock actuator
TAILGATE
BODY
42-48
INSTALLATION SERVICE POINT
>>A<< STRIKER INSTALLATION
Assemble so the distance between the centre of the
striker and centre of the latch is
±
1.5mm or less.
INSPECTION
M1424001200120
TAILGATE LOCK ACTUATOR CHECK
TAILGATE LATCH CHECK <Vehicles for
keyless entry system>
AC006126AB
Striker center
Striker
Latch center
Latch
+1.5 mm
-1.5 mm
AC103292
A
View A
Unlock
Lock
Lever
AC
LEVER
POSITION
BATTERY
CONNECTION
LEVER
OPERATION
At the
"LOCK"
position
•
Connect terminal
No.2 and the
negative battery
terminal.
•
Connect terminal
No.3 and the
positive battery
terminal.
The lever
moves from the
"LOCK"
position to the
"UNLOCK"
position.
At the
"UNLOCK"
position
•
Connect terminal
No.3 and the
negative battery
terminal.
•
Connect terminal
No.2 and the
positive battery
terminal.
The lever
moves from the
"UNLOCK"
position to the
"LOCK"
position.
LEVER
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
At the "LOCK"
position
1
−
2 (Earth)
Open circuit
At the
"UNLOCK"
position
Less than 2
ohms
AC103291
Lever
Unlock
Lock
1
2
AD
KEYLESS ENTRY SYSTEM
BODY
42-49
KEYLESS ENTRY SYSTEM
SPECIAL TOOLS
M1428000600406
Tool
Number
Name
Use
MB991502
MUT-II sub-assembly Encrypted code registration
MB991529
Diagnosis code check
harness
MB991955
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991825
F: MB991826
MUT-III sub-assembly
A: Vehicle
communication
interface (V.C.I.)
B: MUT-III USB cable
C: MUT-III main
harness A
(applicable to
vehicles with CAN
communication)
D: MUT-III main
harness B
(applicable to
vehicles without
CAN
communication)
E: MUT-III
measurement
adapter
F: Trigger harness
Encrypted code registration
CAUTION
MUT-III main harness B
(MB991911) should be used.
MUT-III main harness A should
not be used for this vehicle.
B991502
MB991529
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
A
B
C
D
E
F
DO NOT USED
KEYLESS ENTRY SYSTEM
BODY
42-50
TROUBLESHOOTING
M1428000700351
The keyless entry system is controlled by the Smart
Wiring System (SWS). For troubleshooting, refer to
GROUP 54B, Troubleshooting
or GROUP
54C, Troubleshooting
.
ON-VEHICLE SERVICE
KEYLESS ENTRY SYSTEM CHECK
M1428001400126
Check the system as described below. If the system
does not work, carry out troubleshooting. Refer to
GROUP 54B, Troubleshooting
, refer to
GROUP 54C, Troubleshooting
•
Operate the transmitter to check that the doors
and tailgate can be locked and unlocked.
•
Operate the transmitter to check that the
answerback function works in response to door
and tailgate locking/unlocking.
NOTE:
.
•
The adjustment function allows you to change
the answerback setting as follows. Prior to
that check, confirm which setting is activated.
•
The hazard warning lamps flash twice
when locked and once when unlocked.
The room lamp flashes twice when locked
and illuminates for 15 seconds when
unlocked.
•
The hazard warning lamps do not flash
when locked and flash once when
unlocked. The room lamp flashes twice
when locked and illuminates for 15
seconds when unlocked.
•
The hazard warning lamps flash twice
when locked and do not flash when
unlocked. The room lamp flashes twice
when locked and illuminates for 15
seconds when unlocked.
•
The hazard warning lamps do not flash
when both locked and unlocked. The room
lamp flashes twice when locked and
illuminates for 15 seconds when unlocked.
KEYLESS ENTRY SYSTEM TIMER LOCK
FUNCTION INSPECTION
M1428004000172
Push the transmitter unlock button and check to see
that the doors and tailgate lock within 30 seconds. If
it doesn't, then execute troubleshooting remedies.
Refer to GROUP 54B, Troubleshooting
refer to GROUP 54C, Troubleshooting
.
HOW TO REPLACE THE TRANSMITTER
BATTERY
M1428000900236
CAUTION
Do not allow water or dust to enter the inside of
the transmitter when it is open. Also, do not
touch the precision electronic device.
1. Remove the set screw to remove the battery from
the transmitter.
2. Install a battery with its (+) side face-down.
Battery required for replacement: Coin type
battery CR2032
3. Insert the claw first, and assemble the transmitter.
4. Verify that the keyless entry system operates.
AC000509
Battery
Claw
Screw
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст