Mitsubishi Outlander (2003+). Manual — part 419
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL
54A-71
2. If all checks are correct, go to fuel gauge unit float
height check. If any check is not correct, replace
the fuel gauge unit.
ENGINE COOLANT TEMPERATURE
GAUGE UNIT CHECK
M1543001500439
1. Drain the engine coolant. (Refer to GROUP 14-
On-vehicle Service
.)
2. Remove the engine coolant temperature gauge
unit.
3. Put engine coolant temperature gauge unit into
the hot water in specified temperature, and
ensure that basic resistance is within standard
value.
Standard value: 104
±
13.5
Ω
(at 70C
°
)
Reference value
4. After inspection, apply specified sealant at
threads of engine coolant temperature gauge unit,
and tighten to the specified torque.
Semi-drying sealant: 3M 1215 or equivalent
5. Add engine coolant. (Refer to GROUP 14 -
On-vehicle Service
ACX00779 AI
Circuit tester
Thermometer
Temperature (
°
C)
Resistance
Ω
50 230
60 155
80 73
ACX00780AH
11 ± 1 N·m
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL
54A-72
COMBINATION METER ASSEMBLY
REMOVAL AND INSTALLATION
M1543021300040
AC211662AB
1
2
3
1.5 ± 0.5 N·m
1.5 ± 0.5 N·m
Removal steps
1. Instrument panel driver’s side garnish (Refer
to GROUP 52A, Instrument panel
<LHD> or
<RHD>.)
2. Meter bezel (Refer to GROUP 52A,
<LHD> or
<RHD>.)
3. Combination meter assembly
Removal steps (Continued)
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL
54A-73
DISASSEMBLY AND REASSEMBLY
M1543003100374
AC211663
1
2
3
4
5
AB
1.5 ± 0.5 N·m
Disassembly steps
1. Meter glass
2. Meter panel
3. Circuit board cover
4. Bulb
5. Combination meter assembly
Disassembly steps (Continued)
HEADLAMP
CHASSIS ELECTRICAL
54A-74
HEADLAMP
SERVICE SPECIFICATIONS
M1542000300428
TROUBLESHOOTING
M1542000701430
Features the headlamp automatic shutdown function
to avoid battery drain when the headlamps are left
on. The main features are as follows:
•
Extinguishes automatically in three minutes if the
ignition switch is turned off with the lighting switch
on.
•
Extinguishes in one second if the driver's door is
opened within that 3-minute period.
•
If the headlamps are turned on with the ignition
switch off, the headlamps and tail lamps will
extinguish in three minutes after the driver's door
is opened or closed.
The headlamps are controlled by the Smart Wiring
System (SWS). For troubleshooting, refer to
respective Groups below.
•
Not using SWS monitor: GROUP 54B, SWS
Diagnosis
•
Using SWS monitor: GROUP 54C, SWS
Diagnosis
ON-VEHICLE SERVICE
HEADLAMP AIMING
M1542000900572
PRE-AIMING INSTRUCTIONS
1. Inspect for badly rusted or faulty headlamp
assemblies.
2. These conditions must be corrected before a
satisfactory adjustment can be made.
3. Inspect tyre inflation, and adjust if it is necessary.
4. If the fuel tank is not full, place a weight in luggage
room of the vehicle to simulate weight of a full
tank (0.8 kg per litre).
5. There should be no other load in the vehicle other
than driver or substituted weight of approximately
75 kg placed in driver's position.
6. Thoroughly clean the headlamp lenses.
7. Place the vehicle on a level floor, perpendicular to
a flat screen 10 m away from the bulb
centre-marks on the headlamp lens.
8. Rock vehicle sideways to allow vehicle to assume
its normal position.
9. Bounce the front suspension through three (3)
oscillations by applying the body weight to hood
or bumper.
10.Four lines of adhesive tape (or equivalent
markings) are required on screen or wall:
(1) Position a vertical tape or mark so that it is
aligned with the vehicle centre line.
(2) Measure the distance from the centre-marks
on the headlamp lens to the floor. Transfer the
measurement to the screen. Horizontal tape or
mark on the screen is for reference of vertical
adjustment.
NOTE: Height from the floor to the centre of
the headlamps (Reference value): 840 mm
Item
Standard value
Limit
Headlamp
aiming
Vertical
direction
42 mm (0.24
°
) below horizontal (H)
±
51 mm (
±
0.29
°
) from the standard
value
Horizontal
direction
Position at which the stat up point of
15
°
is crossed with vertical line (V)
±
87 mm (
±
0.5
°
) from the standard
value
AC300909
AB
Headlamp
centre
(1)
(2)
(3)
Headlamp centre
Vehicle centre line
Screen
(3)
10 m
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст