Mitsubishi Outlander (2003+). Manual — part 420
HEADLAMP
CHASSIS ELECTRICAL
54A-75
(3) Measure the distance from the centre line of
the vehicle to the centre of each headlamp.
Transfer the measurement to the screen.
Vertical tape or mark on the screen with
reference to the centre line of each headlamp
bulb.
HEADLAMP ADJUSTMENT
CAUTION
•
Do not cover a headlamp for more than three
minutes to prevent the plastic headlamp lens
deformation.
•
When adjusting one headlamp beam, make
sure that another headlamp is off by
disconnecting the connector from it. When
reconnecting the connector, make sure that
the headlamp beam is not disturbed
accidentally.
1. The low-beam headlamp should project on the
screen upper edge of the beam (cut-off).
2. If not the case, turn the adjusting screws to
achieve the specified low-beam cut-off location on
the aiming screen.
Standard value:
(Vertical direction) 42 mm (0.24
°
) below
horizontal (H)
(Horizontal direction) Position at which the
stat up point of 15
°
is crossed with vertical
line (V)
Limit:
Vertical direction;
±
51 mm (
±
0.29
°
) from the
standard value
Horizontal direction;
±
87 mm (
±
0.5
°
) from
the standard value
LUMINOUS INTENSITY MEASUREMENT
M1542001000505
1. Set the headlamps to high-beam
2. Using a photometer, and following its
manufacturer's instruction manual, measure the
headlamp centre intensity and check to be sure
that the limit value is satisfied.
Limit: 30,000 cd or more {When a screen is
set 25m ahead of the vehicle}
NOTE: When measuring the intensity, maintain an
engine speed of 2,000 r/min., with the battery fully
charged.
There may be special local regulations pertaining to
headlamp intensity. Be sure to make any
adjustments necessary to satisfy such regulations.
If an illuminometer is used to make the
measurements, convert its values to photometer
values by using the following formula.
I =E x r
2
:
•
I = intensity (cd)
•
E = illumination (lux)
•
r = distance (m) from headlamps to illuminometer
AC300115
Vertical
direction
AB
Vertical direction
ACX01800AD
Distance of
vertical direction
[42 mm (0.24˚)]
Headlamp centre
High intensity
zone
15˚
(H)
(V)
HEADLAMP
CHASSIS ELECTRICAL
54A-76
BULB REPLACEMENT
M1542001300733
Headlamp Bulb
CAUTION
Do not touch the surface of the bulb with hands
or dirty gloves as the bulb may pop after a short
time. If the surface does become dirty, clean it
with alcohol or thinner, and let it dry thoroughly
before installing.
1. Disconnect the headlamp connector.
2. Remove the socket cover, and then remove the
bulb.
Position Lamp Bulb
CAUTION
•
As a principal, the position lamps can be
removed as individual part. If not, remove the
position lamp from the headlamp and position
lamp assembly, and then remove the position
lamp from the headlamp. Then replace the
bulb.
•
Do not touch the bulb surface bare-handed or
with dirty gloves. If dirt is attached on surface
of the bulb, immediately use alcohol or
thinner to remove dirt, and install the bulb
after well dried.
1. Screw out the position lamp socket.
2. Disconnect the connector.
Front Turn-Signal Lamp bulb
CAUTION
Do not touch the bulb surface bare-handed or
with dirty gloves. If dirt is attached on surface of
the bulb, immediately use alcohol or thinner to
remove dirt, and install the bulb after well dried.
Disconnect the connector, and screw out the front
turn-signal lamp socket.
AC300097
Socket cover
AB
AC300089
AB
Position lamp socket
AC300098
AB
Front turn-signal
lamp socket
HEADLAMP
CHASSIS ELECTRICAL
54A-77
HEADLAMP
REMOVAL AND INSTALLATION
M1542001800255
REMOVAL SERVICE POINT
<<A>> HEADLAMP ASSEMBLY REMOVAL
1. Remove half of the front bumper assembling clips
and bolts.
NOTE: The Figure illustrates the procedures to
remove the headlamp assembly (LH).
2. Slide the front bumper down to remove the
headlamp assembly.
Post-installation Operation
Headlamp Aiming Adjustment (Refer to
AC300070 AB
4.9 ± 0.7 N·m
1
2
Removal steps
1.
Radiator grill
<<A>>
2.
Headlamp assembly
AC201812 AD
HEADLAMP
CHASSIS ELECTRICAL
54A-78
HEADLAMP LEVELING SWITCH
REMOVAL AND INSTALLATION
M1542013700051
INSPECTION
M1542011200997
HEAD LAMP LEVELING SWITCH
RESISTANCE CHECK
AC210845AE
2
1
Removal steps
1. Instrument lower panel (Refer to GROUP
52A, Instrument panel assembly
<LHD> or
<RHD>.)
2. Headlamp leveling switch
AC212497AB
Terminal No.
Switch
position
Resistance
4 - 6
0
750 ohms
1
1050 ohms
2
1410 ohms
3
1710 ohms
4
2010 ohms
5 - 6
0, 1, 2, 3, 4
2830 ohms
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст