Mitsubishi Outlander (2003+). Manual — part 564
TROUBLESHOOTING
AUTOMATIC AIR CONDITIONER
55B-71
STEP 4. Connector check: C-27 A/C-ECU
connector and C-123 photo sensor connector.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair or replace the connector.
STEP 5. Check the wiring harness between C-123
photo sensor connector (terminal 1, 2) and C-27
A/C-ECU connector (terminal 19, 9).
•
Check the photo sensor signal lines for open or
short circuit.
Q: Is the check result normal?
YES :
Replace the Photo sensor.
NO :
Repair the wiring harness.
AC308718
Connector: C-27
AU
C-27(B)
<LHD>
8
2
10 9
1
5
3
4
6
7
20191817161514131211
Harness side
AC308735
Connector: C-27
BB
C-27(B)
Harness side
<RHD>
8
2
10 9
1
5
3
4
6
7
20191817161514131211
AC308716
Connector: C-123
AZ
C-123
Harness side
<LHD>
1
2
AC308769
BE
C-123
Connector: C-123
<RHD>
1
2
Harness side
AC308718
Connector: C-27
AU
C-27(B)
<LHD>
8
2
10 9
1
5
3
4
6
7
20191817161514131211
Harness side
AC308735
Connector: C-27
BB
C-27(B)
Harness side
<RHD>
8
2
10 9
1
5
3
4
6
7
20191817161514131211
AC308716
Connector: C-123
AZ
C-123
Harness side
<LHD>
1
2
AC308769
BE
C-123
Connector: C-123
<RHD>
1
2
Harness side
TROUBLESHOOTING
AUTOMATIC AIR CONDITIONER
55B-72
INSPECTION PROCEDURE 7: The A/C indicator flashes.
CIRCUIT OPERATION
If the A/C indicator flashes then the possible causes
may be due to a defective A/C pressure system or
insufficient refrigerant gas.
TROUBLESHOOTING HINTS
•
Malfunction of the A/C pressure sensor
•
Malfunction of the outside thermo sensor
•
Malfunction of the A/C-ECU
DIAGNOSIS
STEP 1. Check the A/C pressure sensor
operation.
Refer to GROUP 55A, On vehicle service
−
A/C
pressure sensor check
Q: Is the A/C pressure sensor operating properly?
YES :
Go to Step 2.
NO :
Replace the A/C pressure sensor.
STEP 2. Check the outside thermo sensor.
Refer to
Q: Is the outside thermo sensor in good condition?
YES :
Go to Step 3.
NO :
Replace the air thermo sensor.
STEP 3. Check the refrigerant level.
Refer to GROUP 55A, On vehicle service
−
sight
Q: Is the refrigerant level correct?
YES :
Replace the automatic air conditioner
control panel (A/C-ECU).
NO :
Correct the refrigerant level. (Refer to
GROUP 55A, On-vehicle Service
).
A/C-ECU
A/C PRESSURE
SENSOR
OUTSIDE
THERMO
SENSOR
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
TROUBLESHOOTING
AUTOMATIC AIR CONDITIONER
55B-73
INSPECTION PROCEDURE 8: The inside/outside air changeover is impossible.
COMMENTS ON TROUBLE SYMPTOM
When inside air cannot be changed to outside air
vice versa even if its changeover switch is on, the
outside/inside air selection damper control motor
system may be defective.
Possible causes
•
Malfunction of the outside/inside air selection
damper control motor
•
Damaged the wiring harness or connectors
•
Malfunction of the automatic air conditioner
control panel (A/C-ECU)
DIAGNOSIS
Step 1. MUT-II/III actuator test
Carry out the actuator test.
•
Item 13, 14: outside/inside air selection damper
control motor
Q: Does the blower motor work normally?
YES :
Replace the automatic air conditioner
control panel (A/C-ECU)
NO :
Go to Step 2.
Step 2. Measure the voltage at C-311
outside/inside air selection damper control motor
connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
A/C-ECU
IGNITION
SWITCH (IG2)
MOTOR DRIVE
CIRCUIT
OUTSIDE/INSIDE AIR
SELECTION DAMPER
CONTROL MOTOR
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Outside/Inside Air Selection Damper Control Motor Circuit
AC308739
AH
C-311
Connector: C-311
<LHD>
Harness side
6
2
7
3
5 4
1
AC308739
AG
C-311
Connector: C-311
<RHD>
Harness side
6
2
7
3
5 4
1
TROUBLESHOOTING
AUTOMATIC AIR CONDITIONER
55B-74
(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between terminal 7 and
body earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 3.
Step 3. Connector check: C-311 outside/inside air
selection damper control motor connector
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the connector.
AC301541
6
2
7
3
5 4
1
BT
Connector C-311
(Harness side)
AC308739
AH
C-311
Connector: C-311
<LHD>
Harness side
6
2
7
3
5 4
1
AC308739
AG
C-311
Connector: C-311
<RHD>
Harness side
6
2
7
3
5 4
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст