Mitsubishi Outlander (2003+). Manual — part 339
DOOR MIRROR
EXTERIOR
51-55
STEP 13. Connector check: C-205 junction block
connector
Q: Is the check result normal?
YES :
Go to Step 14.
NO :
Repair the defective connector.
STEP 14. Measure the voltage at the E-06 door
mirror assembly (LH) connector.
(1) Turn the ignition switch to the ON position.
(2) Defogger switch: ON
(3) Disconnect the connector, and measure at the
wiring harness side.
(4) Voltage between E-06 door mirror assembly
connector terminal No.1 and body earth
OK: System voltage
Q: Is the check result normal?
YES :
Intermittent malfunction (Refer to GROUP
00
−
How to Cope with Intermittent
Malfunction
NO :
Go to Step 15.
STEP 15. Check the wiring harness between E-06
door mirror assembly (LH) connector terminal
No.1 and C-205 junction block connector
terminal No.3.
•
Check the power supply line for open circuit.
AC210474
Connector: C-205
Harness side
AE
21
7
16 15
17
18
20 19
1
2
3
4
5
6
23 22
24
25
28
26
27
9
8
10
11
14
12
13
Junction block (Front view)
AC301418
Connector: E-06
E-06
Harness side
AE
2
7 6
1
3
5 4
2
7 6
1
3
5 4
AC301695
Connector E-06
(harness side)
AC
AC301418
Connector: E-06
E-06
Harness side
AE
2
7 6
1
3
5 4
AC210474
Connector: C-205
Harness side
AE
21
7
16 15
17
18
20 19
1
2
3
4
5
6
23 22
24
25
28
26
27
9
8
10
11
14
12
13
Junction block (Front view)
DOOR MIRROR
EXTERIOR
51-56
NOTE:
Prior to the wiring harness inspection, check
intermediate connector C-118 <L.H. driver vehicles>
and C-34 <R.H. driver vehicles>, and repair if
necessary.
Q: Is the check result normal?
YES : .
Intermittent malfunction (Refer to GROUP
00
−
How to Cope with Intermittent
Malfunction
NO : .
Repair the wiring harness.
AC308716
AH
Connector: C-118
<LHD>
32
22
11
27
16
5
24
13
2
12
23
1
15
14
26
25
3 4
29
19
8
18
17
28
6 7
21
20
30 31
9 10
AC308735
Connector: C-34
<RHD>
AG
C-34(GR)
13
3
7
16
19
15
14
18
17
12
6
4
8
1
9
11
10
5
2
DOOR MIRROR
EXTERIOR
51-57
DOOR MIRROR
REMOVAL AND INSTALLATION
M1511006400405
AC201696
7
Section A – A
Section B – B
Clip
AB
6
1
Claw
Claw
3
4
5
3
B
B
A
1
A
A
2
Door mirror removal steps
1. Delta cover
2. Tweeter
>>A<<
3. Door mirror assembly
4. Door mirror body assembly
<<A>>
5. Mirror
Remote controlled mirror switch
removal steps
6. Instrument panel lower cover (Refer
to GROUP 52A, Instrument panel
<L.H. drive vehicles>,
<R.H. drive vehicles>.)
7. Remote controlled mirror switch
DOOR MIRROR
EXTERIOR
51-58
REMOVAL SERVICE POINT
<<A>> MIRROR REMOVAL
CAUTION
The thumb of the mirror is prone to breakage
when working in cold temperatures. Always
warm up the mirror thumb and thumb periphery
to 20
°
C or higher before handling.
Slant the mirror upward with your hands. Then insert
a flat-tipped screwdriver wrapped with protective
tape between the pivot plate and mirror through the
cut-out from behind the mirror. Now pry off the mirror
thumb and remove the mirror as shown.
INSTALLATION SERVICE POINT
>>A<< DELTA COVER INSTALLATION
CAUTION
If the delta cover is placed with the clip on the
door panel, the clip may be pushed into the door
panel and fall off. Thus, special care is
necessary.
Install the delta cover with the clip installed.
AC103244
AC
Section A – A
Mirror
Flat-tipped
screwdriver
Flat-tipped
screwdriver
Mirror
A
A
Protective tape
Notch
Claw
Claw
Claw
Pivot plate
AC107642
Clip
Section A – A
A
A
Delta cover
Delta cover
Clip
Door panel
AB
A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст