Mitsubishi Outlander (2003+). Manual — part 340
DOOR MIRROR
EXTERIOR
51-59
>>B<< DOOR MIRROR ASSEMBLY
INSTALLATION
CAUTION
When assembling the door mirror, check to see
that the thumb of the door mirror is inserted in
the cut-out of the front door runchannel.
INSPECTION
M1511006500350
ELECTRIC REMOTE CONTROL MIRROR
OPERATION CHECK
Check that the mirror moves as described in the
table when each terminal is connected to the battery.
AC103753
Section A – A
A
A
Notch
Door mirror
claw position
Door panel
Runchannel
Door mirror
Door mirror
claw position
Runchannel
AC
Battery connection
Direction
operation
•
Connect terminal 5 to the negative
battery terminal.
•
Connect terminal 7 to the positive
battery terminal.
Up
•
Connect terminal 5 to the positive
battery terminal.
•
Connect terminal 7 to the negative
battery terminal.
Down
•
Connect terminal 5 to the negative
battery terminal.
•
Connect terminal 6 to the positive
battery terminal.
Right
•
Connect terminal 5 to the positive
battery terminal.
•
Connect terminal 6 to the negative
battery terminal.
Left
DOOR MIRROR
EXTERIOR
51-60
DOOR MIRROR CONTROL SWITCH CONTINUITY
CHECK
HEATED DOOR MIRROR CHECK
CAUTION
When relocating the car between locations with
extremely different temperatures (warm and
cold), leave the car in the location for a while to
adapt to the temperature prior to checking it.
Check to see that the resistance shown in the graph
is almost satisfied when measuring the resistance of
terminal 1 and 2 of the door mirror connectors under
2 or more different temperature conditions.
Switch position
Tester
connection
Specified
condition
OFF
9
−
2, 9
−
3, 9
−
6,
9
−
10, 9
−
11, 1
−
2, 1
−
3, 1
−
6, 1
−
10, 1
−
11
Open circuit
Left side OFF
9
−
6, 9
−
10, 9
−
11, 1
−
6, 1
−
10,
1
−
11
Open circuit
Up
1
−
6, 9
−
11
Less than 2
ohms
Down
1
−
11, 6
−
9
Right
1
−
6, 9
−
10
Left
1
−
10, 6
−
9
Right
side
OFF
9
−
2, 9
−
3, 9
−
6,
1
−
2, 1
−
3, 1
−
6
Open circuit
Up
1
−
6, 3
−
9
Less than 2
ohms
Down
1
−
3, 6
−
9
Right
1
−
6, 2
−
9
Left
1
−
2, 6
−
9
AC005970
2
1
4
3
5
10
9
8
7
6
11
AC201611
Resistance
Temperature (˚C)
-10
0
10
20
30
40
(
Ω
)
0
2
4
6
8
10
AC
12
Upper limit value
Lower limit value
52A-1
GROUP 52A
INTERIOR
CONTENTS
SPECIAL TOOL . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL ASSEMBLY*.
REMOVAL AND INSTALLATION
<L.H. DRIVE VEHICLES>. . . . . . . . . . . . . .
DISASSEMBLY AND REASSEMBLY. . . . .
REMOVAL AND INSTALLATION
<R.H. DRIVE VEHICLES> . . . . . . . . . . . . .
DISASSEMBLY AND REASSEMBLY. . . . .
FLOOR CONSOLE ASSEMBLY . . . .
REMOVAL AND INSTALLATION . . . . . . . .
DISASSEMBLY AND REASSEMBLY. . . . .
TRIMS. . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
DOOR TRIM . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
DISASSEMBLY AND REASSEMBLY. . . . .
TAILGATE TRIM . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
HEADLINING . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSIDE REAR VIEW MIRROR . . . . . .
FRONT SEAT ASSEMBLY* . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
DISASSEMBLY AND REASSEMBLY . . . . .
REAR SEAT ASSEMBLY. . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
DISASSEMBLY AND REASSEMBLY . . . . .
FRONT SEAT BELT* . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
REAR SEAT BELT . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
WANINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING
•
Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and
paassenger (from rendering the SRS inoperative).
•
Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.
•
MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any
SRS-related component.
NOTE
The SRS includes the following components: SRS air bag control unit, SRS warning light, front impact sensors, air bag module,
clock spring, and interconnecting wiring. Other SRS-related components (that may have to be removed/installed in connection
with SRS service or maintenance) are indicated in the table of contents by an asterisk (*).
SPECIAL TOOL
INTERIOR
52A-2
SPECIAL TOOL
M1521000600264
INSTRUMENT PANEL ASSEMBLY
REMOVAL AND INSTALLATION
<L.H. DRIVE VEHICLES>
M1521001700491
WARNING
For removal and installation of the passenger's side air bag module, always observe the
service procedures described in GROUP 52B, Air Bag Module and Clock Spring
.
The following bolts and screws are used for installing the instrument panel. Bolts and screws are indicated as
marks shown in the illustration in the sections of "Removal and Installation" and "Disassembly and
Assembly."
Tool
Tool number
Name
Use
MB990784
Ornament remover
Removal of switch, trim, etc.
MB990784
Name
Symbol
Size (D
×
L) mm
Colour
Shape
Tapping screw
a
5
×
12
-
b
5
×
16
-
c
5
×
16
Black
d
5
×
12
-
e
5
×
20
-
Washer assembly bolt
f
6
×
16
-
g
6
×
16
-
h
6
×
16 (Earth)
-
i
8
×
20
-
j
10
×
60
-
AC104450
AC104436
AC104417
AC200304
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст