Mitsubishi Outlander (2003+). Manual — part 295
GENERAL INFORMATION
POWER STEERING
37A-3
GENERAL INFORMATION
M1372000100412
FEATURES
Power steering has been adopted in all vehicles to
make the steering system easier to handle.
•
A 4-spoke steering wheel is used.
•
A steering column has a shock absorbing
mechanism and a tilt steering mechanism.
•
Integral-type rack and pinion gear with high
rigidity and excellent response is used.
•
A vane type pump with a fluid flow rate control
system which change steering effort according to
the engine speed is used.
•
The separate plastic resin oil reservoir is used to
reduce weight and to make the fluid level
checking easier.
•
The cooler tube assembly is installed on the
power steering fluid line to improve the cooling
performance of the power steering fluid.
SPECIFICATIONS
Item
Specification
Steering wheel
Type
4-spoke type
Outside diameter mm
380
Maximum number of turns
2.7
Steering column
Column mechanism
Shock absorbing mechanism and Tilt
steering mechanism
Tilt up: 20 mm
Tilt down: 20 mm
Power steering type
Integral type
Oil pump
Type
Vane pump
Basic discharge amount mL/rev.
9.6
Relief pressure MPa
8.8
Reservoir type
Separate type (plastic)
Pressure switch
Equipped
Steering gear
Type
Rack and pinion
Stroke ratio (Rack stroke/Steering wheel
maximum turning radius)
51.45
Rack stroke mm
141
GENERAL INFORMATION
POWER STEERING
37A-4
CONSTRUCTION DIAGRAM
AC300061AB
Steering wheel
Steering column
shaft assembly
Pressure hose
assembly
Oil reservoir
Suction hose
Return hose
Oil pump assembly
Steering gear
Cooler tube assembly
SERVICE SPECIFICATIONS
POWER STEERING
37A-5
SERVICE SPECIFICATIONS
M1372000300449
LUBRICANTS
M1372000400413
Item
Standard value
Limit
Steering wheel free
play mm
With engine running
−
30
With engine stopped
10 or less
−
Steering angle
Inside wheel
34
°
50'
±
1
°
30'
−
Outside wheel (reference)
29
°
20'
−
Toe-in
At the centre of tyre tread mm
1
±
2
−
Toe-angle (per wheel)
0
°
03'
±
05'
−
Tie rod end ball joint starting torque N
⋅
m
0.5
−
2.5
−
Tie rod swing resistance N [Tie rod swing torque N
⋅
m]
6
−
19 [1.5
−
4.9]
−
Stationary steering effort N [Fluctuation allowance N]
29 or less [5.9 or less]
−
Oil pump pressure
MPa (750
±
100 r/min.)
Oil pump relief pressure
8.8
−
9.5
−
Pressure under no-load conditions
0.8
−
1.0
−
Steering gear retention hydraulic pressure 8.8
−
9.5
−
Oil pressure switch operating pressure
MPa
OFF
→
ON
1.5
−
2.0
−
ON
→
OFF
0.7
−
2.0
−
Steering gear total pinion torque N
⋅
m [Change in torque N
⋅
m]
0.7
−
1.6 [0.4 or less]
−
Opening dimension of special tool boot band crimping tool
(MB991561) mm
2.9
−
Band crimped width mm
2.4
−
2.8
−
Item
Specified lubricant
Quantity
Power steering fluid
ATF DEXRON III or DEXRON II Approximately 1.0 L
Steering gear
Bearing
ATF DEXRON III or DEXRON II As required
O-ring and seal ring
Oil seal
Special tool (MB991213)
Pinion and valve assembly
seal ring part
Bellows
Silicon grease
As required
Tie rod end ball joint
Multipurpose grease SAE J310,
NLGI No.2 or equivalent
As required
Oil pump
Friction surface of rotor vane,
cam ring and pump cover
ATF DEXRON III or DEXRON II As required
O-ring
SEALANTS
POWER STEERING
37A-6
SEALANTS
M1372000500421
SPECIAL TOOLS
M1372000600440
Item
Specified sealant
Steering shaft cover assembly bolt hole on the toeboard
3M ATD Part No.8513 or equivalent
Steering gear
End plug
3M ATD Part No.8661, 8663 or
equivalent
Rack support cover
Tool
Number
Name
Use
MB991897
Ball joint remover
Knuckle and tie rod end ball joint
disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113) is also
available to disconnect knuckle and
tie rod end ball joint.
MB990326
Preload socket
Tie rod end ball joint starting torque
check
MB991548
Power steering oil
pressure gauge
adapter (Pump
side)
Oil pump pressure test
MB991549
Power steering oil
pressure gauge
adapter (Hose
side)
MB990662
Power steering oil
pressure gauge
MB990784
Ornament remover Cover removal
AC106827
MB990326
MB991548
MB991549
MB990662
MB990784
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст