Mitsubishi Outlander (2003+). Manual — part 277
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-51
NOTE:
After inspecting combination meter connector C-05,
ABS-ECU connector B-03 and intermediate
connector C-105, inspect the wire. If any of these
connectors is damaged, repair or replace it. Then go
to Step 7.
Q: Is the harness wire between the combination meter
connector C-05 terminal 18 and ABS-ECU
connector B-03 terminal 12 damaged?
YES :
Repair the harness wire and go to Step 7.
NO :
Replace the combination meter and go to
Step 7.
STEP 7. Retest the system.
Q: Does the ABS warning lamp illuminate for 3
seconds when the ignition switch is turned to the
"ON" position with engine stopped or upon
start-up?
YES :
The procedure is complete.
NO :
Start over at Step 1.
AC308718
AR
C-105
Connector: C-105
<LHD>
10
1
21
16
13
4
11
2
12
3
1415
1718
5
20
7
19
6
8
22
9
AC308735
AW
C-105
Connector: C-105
<RHD>
10
1
21
16
13
4
11
2
12
3
1415
1718
5
20
7
19
6
8
22
9
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-52
INSPECTION PROCEDURE 3: The ABS Warning Lamp Remains Illuminated after the Engine is
Started.
NOTE: This diagnosis procedure is limited to cases where communication with the MUT-II/III is possible
(ABS-ECU power supply is normal) and no diagnosis code outputs.
OPERATION
Refer to
.
COMMENT ON TROUBLE SYMPTOM
Disconnected ABS warning lamp output line of
ABS-ECU is suspected.
PROBABLE CAUSES
The most likely causes for this case are:
•
Damaged wiring harness or connector
•
Malfunction of the hydraulic unit (integrated with
ABS-ECU)
•
Malfunction of the combination meter
ABS-ECU
IGNITION
SWITCH (IG1)
COMBINATION
METER
<LHD>
CPU
<RHD>
<LHD>
<RHD>
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
ABS Warning Lamp Circuit
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-53
DIAGNOSIS
STEP 1. Check the ABS warning lamp circuit at
ABS-ECU connector B-03.
(1) Disconnect ABS-ECU connector B-03.
(2) Connect ABS-ECU connector B-03 terminal
number 12 to earth.
(3) Turn the ignition switch to the "ON" position.
Q: Does the ABS warning lamp go off?
YES :
To check and reproduce the state of
malfunction replace the hydraulic unit
(integrated with ABS-ECU). Then go to Step
3. If the malfunction is not reproduced, an
intermittent malfunction is suspected. Refer
to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
−
How to Cope With Intermittent Malfunction
.
NO :
Go to Step 2.
AC301441AB
Connector: B-03
B-03 (GR)
Harness side
AC301683AF
Connector B-03
(harness side)
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-54
STEP 2. Check the harness wire between the
combination meter connector C-05 terminal 18
and ABS-ECU connector B-03 terminal 12.
NOTE:
After inspecting combination meter connector C-05,
ABS-ECU connector B-03 and intermediate
connector C-105, inspect the wire. If any of these
connectors is damaged, repair or replace it. Then go
to Step 3.
Q: Is the harness wire between combination meter
connector C-05 terminal 18 and ABS-ECU
connector B-03 terminal 12 damaged?
YES :
Repair the harness wire and then go to Step
NO :
Replace the combination meter (printed
circuit board) and then go to Step 3.
STEP 3. Retest the system.
Q: Does the ABS warning lamp turn off in 3 seconds
after start-up?
YES :
The procedure is complete.
NO :
Start over at Step 1.
AC308716
AT
C-05 (L)
Connector: C-05
<LHD>
Harness side
G
G
22
11
5
16
19
20
21
17
18
8
10 9
7 6
13
1514
12
2
4 3
1
AC308769
AW
C-05 (L)
Connector: C-05
<RHD>
Harness side
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
AC301441AB
Connector: B-03
B-03 (GR)
Harness side
AC308718
AR
C-105
Connector: C-105
<LHD>
10
1
21
16
13
4
11
2
12
3
1415
1718
5
20
7
19
6
8
22
9
AC308735
AW
C-105
Connector: C-105
<RHD>
10
1
21
16
13
4
11
2
12
3
1415
1718
5
20
7
19
6
8
22
9
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст