Mitsubishi Outlander (2003+). Manual — part 348
FRONT SEAT ASSEMBLY
INTERIOR
52A-31
INSTALLATION SERVICE POINT
>>A<< FRONT SEAT ASSEMBLY INSTALLATION
1. Temporarily tighten the nuts and bolts in all
mounting locations shown in the illustration with
no load applied to the front seat cushion and
check the operation of the seat slide.
2. Tighten the nuts and bolts in all mounting
locations to the specified torque.
INSPECTION
M1522005500061
HEATED SEAT SWITCH CHECK
1. Check for continuity between terminals.
2. Check that the indicator is lighted at HI or LO
when battery voltage is supplied to terminal 5, and
terminal 8 is grounded.
3. Check that indicator is lighted when battery
voltage is supplied to terminals 2 and 6.
SEAT CUSHION HEATER CHECK
Measure the resistance between terminals.
Standard value:
AC301696 AB
ACX00625
Switch position
Tester connection
Specified condition
Driver's seat side
HI
1 - 3, 1 - 5, 1 - 8, 3 - 5, 3 -
8, 5 - 8
Less than 2 ohms
OFF
1 - 3, 1 - 5, 1 - 8, 3 - 5, 3 -
8, 5 - 8
Open circuit
LO
3 - 5, 3 - 8, 5 - 8
Less than 2 ohms
Front passenger's seat
side
HI
4 - 5, 4 - 8, 4 - 9, 5 - 8, 5 -
9, 8
−
9
Less than 2 ohms
OFF
4 - 5, 4 - 8, 4 - 9, 5 - 8, 5 -
9, 8 - 9
Open circuit
LO
5 - 8, 5 - 9, 8 - 9
Less than 2 ohms
1
2 3
AC200099
Measured
terminals
Resistance
value
Note
2
−
3
Approximately
4.8
Ω
±
10 %
At room temperature
20
°
C
1
−
3
5.2
Ω
±
10 %
FRONT SEAT ASSEMBLY
INTERIOR
52A-32
SEATBACK HEATER CHECK
Measure the resistance between terminals.
Standard value: Approximately 4.8
Ω
±
10 %
(At room temperature 20
°
C)
HEATED SEAT RELAY CONTINUITY
CHECK
1
2
AC200100
Battery voltage
Tester
connection
Specified
condition
Not applied
1 - 4
Open circuit
•
Connect
terminal 3 to the
positive battery
terminal
•
Connect
terminal 2 to the
negative battery
terminal
1 - 4
Less than 2
ohms
1
4
3
2
1
3
2
4
AC300127
Junction block
Heated seat relay
AB
FRONT SEAT ASSEMBLY
INTERIOR
52A-33
DISASSEMBLY AND REASSEMBLY
M1522001500490
<L.H. DRIVE VEHICLES>
AC309456
Section A – A
27
10, 11
Claw
AB
12
20 15
17 16
21
18
19
18
4
13
14
9
6
7
8
5
1
3
2
10
24
25
27
24
11
22
26
23
7.6 ± 0.7 N·m
44 ± 10 N·m
A
A
A
12 ± 2 N·m
44 ± 10 N·m
A
NOTE
: Claw position
N
N
Disassembly steps
1.
Reclining knob
2.
Pin
3.
Height adjuster knob
4.
Heater harness assembly
<Vehicles with heated seat>
5.
Front seat cushion assembly
6.
Front seat cushion cover
7.
Front seat cushion pad
8.
Front seat cushion frame
9.
Seat cushion heater <Vehicles with
heated seat>
10. Reclining cover
11. Shield cover
12. Front seatback assembly
13. Lumbar support cap
14. Lumbar support lever
<<A>>
15. Headrest guide
16. Front seatback cover
17. Front seatback pad
18. Lumber support clip
19. Lumber support
20. Front seatback frame
21. Seatback heater <Vehicles with
heated seat>
22. Inner seat belt
23. Shaft
24. Pin
25. Slide handle
26. Shaft protector
27. Seat slide adjuster
Disassembly steps (Continued)
FRONT SEAT ASSEMBLY
INTERIOR
52A-34
<R.H. DRIVE VEHICLES>
AC309458
NOTE
: Claw position
Section A – A
Claw
22
8, 9
9 ± 2 N·m
44 ± 10 N·m
12 ± 2 N·m
A
A
A
A
44 ± 10 N·m
10
14
15
13
16
11
12
4
5
6
7
1
2
3
8
19
20
22
19
21
18
17
9
AB
Disassembly steps
1.
Reclining knob
2.
Pin
3.
Height adjuster knob
4.
Front seat cushion assembly
5.
Front seat cushion cover
6.
Front seat cushion pad
7.
Front seat cushion frame
8.
Reclining cover
9.
Shield cover
10. Front seatback assembly
11. Pin (Driver’s side)
12. Arm rest assembly (Driver’s side)
<<A>>
13. Headrest guide
14. Front seatback cover
15. Front seatback pad
16. Front seatback frame
17. Inner seat belt
18. Shaft
19. Pin
20. Seat slide handle
21. Shaft protector
22. Seat slide adjuster
Disassembly steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст