Mitsubishi Outlander (2003+). Manual — part 332
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-27
WINDSHIELD WASHER FLUID EJECTION CHECK
Move the nozzle to adjust the position so that the
spray is in the area shown in the illustration.
AC107158 AB
50
50
50
50
110
120
600
90
70
60
70
120
<Right>
<Left>
Windshield washer
nozzle perpendicular
Windshield ceramic
line terminal
Units: mm
Windshield washer
nozzle perpendicular
310
130
120
120
285
Windshield washer nozzle
<L.H.DRIVE VEHICLE>
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-28
WINDSHIELD WASHER SWITCH CHECK
<L.H.DRIVE VEHICLE>
Check continuity between the switch terminals.
<R.H.DRIVE VEHICLE>
NOTE: The windshield washer switch is integrated in
the column-ECU, so can not be checked as an
individual part. However, its operation can be
checked by the input signal check.
.
•
Not using SWS monitor: Refer to GROUP 54B,
SWS Diagnosis
.
•
Using SWS monitor: Refer to GROUP 54C, SWS
Diagnosis
AC300509 AB
50
50
50
50
110
120
600
90
70
60
70
120
<Right>
<Left>
Windshield washer
nozzle perpendicular
Windshield ceramic
line terminal
Units: mm
Windshield washer
nozzle perpendicular
310
130
120
120
285
Windshield washer nozzle
<R.H.DRIVE VEHICLE>
1
6
8
11
10
9
7
5
4
3
2
AC000417
Switch position
Tester
connection
Specified
condition
OFF
6
−
7
Open circuit
Windshield
washer switch
6
−
7
Less than 2
ohms
REAR WIPER AND WASHER
EXTERIOR
51-29
REAR WIPER AND WASHER
SERVICE SPECIFICATION
M1511000300303
TROUBLESHOOTING
M1511000700442
The rear wiper and washer are controlled by the
smart wiring system (SWS). For troubleshooting,
refer to GROUP 54B, Troubleshooting
GROUP 54C, Troubleshooting
ON-VEHICLE SERVICE
CHECK OF REAR WIPER OPERATION
WHEN SELECTOR LEVER IS AT THE "R"
POSITION
M1511022100040
1. When the selector lever is moved to the "R"
position with the rear wiper switch at the "INT"
position, the wiper should operate twice or three
times at low speed after approximately one
second.
2. If not, troubleshoot the system (Refer to GROUP
54B, Troubleshooting
or GROUP 54C,
Troubleshooting
Item
Standard value
Rear wiper arm and blade assembly stop position (Distance from end wiper
blade and the end of tailgate galss) mm
30
±
5
REAR WIPER AND WASHER
EXTERIOR
51-30
REAR WIPER AND WASHER
REMOVAL AND INSTALLATION
M1511008500215
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 54A, Column switch
Pre-removal and Post-installation Operation
Washer Tank Assembly and Rear Washer Motor Removal
and Installation (Refer to
).
AC300618
6
7.4 ± 1.4 N·m
5
2
4
5.4 ± 1.4 N·m
AB
1
3
Wiper blade assembly removal steps
1. Wiper blade assembly
>>B<<
2. Wiper blade
Rear wiper motor removal steps
>>A<<
3. Wiper arm and blade assembly
•
Tailgate lower trim (Refer to GROUP
52A, Tailgate trim
•
Tailgate waterproof film (Refer to
GROUP 42, Tailgate
4. Rear wiper motor assembly
Rear washer nozzle removal steps
•
High-mounted stop lamp assembly
(Refer to GROUP 54A, High-mounted
stop lamp
5. Rear washer nozzle
Washer hose removal steps
•
Cowl side trim, front scuff plate,
center pillar trim lower, rear scuff
plate, rear pillar trim and rear shelf
trim (Refer to GROUP 52A, Trims
•
Tailgate lower trim, tailgate side trim,
tailgate upper trim (Refer to GROUP
52A, Tailgate trim
•
High-mounted stop lamp assembly
(Refer to GROUP 54A, High-mounted
stop lamp
6. Rear washer hose
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст