Mitsubishi Outlander (2003+). Manual — part 330
UNDER COVER
EXTERIOR
51-19
UNDER COVER
REMOVAL AND INSTALLATION
M1511019600108
AC107344
1
1
2
4
5
3
Splash shield
Splash shield
Front bumper assembly
AB
Removal steps
1. Front bumper assembly mounting
clips
2. Front under cover (LH)
3. Front under cover (RH)
4. Side under cover (LH)
5. Side under cover (RH)
Removal steps (Continued)
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-20
WINDSHIELD WIPER AND WASHER
SERVICE SPECIFICATION
M1511000300392
TROUBLESHOOTING
M1511000700431
The windshield wiper and washer are controlled by
the smart wiring system (SWS). For troubleshooting,
refer to GROUP 54B, Troubleshooting
GROUP 54C, Troubleshooting
NOTE: Even when the ETACS-ECU has failed, the
windshield wiper can work at low speed in fail-safe
mode. (Normally, the windshield wiper operates
when the ignition switch is at the "ACC" or "ON"
position. But, if it enters the fail-safe mode, the wiper
can operate only when the ignition switch is at the
"ON" position).
Item
Standard value
Stop position of the windshield wiper arm/blade assembly (Distance between
the edge of the wiper blade and the end of the deck garnish) mm
Driver’s side: 35
±
5
Passenger’s side: 25
±
5
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-21
WINDSHIELD WIPER
REMOVAL AND INSTALLATION
M1511007900180
AC107419AB
Section B – B
Section C – C
Section D – D
4
5
6
6
6
6
Claw
Clip
Claw
1
2
4
5
7.4 ± 1.4 N·m
8
9
7
A
27 ± 2 N·m
View A
NOTE
: Clip position
: Claw position
B
B
C
C
Windshield
D
D
3
Wiper blade removal steps
1. Wiper blade assembly
>>B<<
2. Wiper blade
Windshield wiper motor and link
assembly removal steps
>>A<<
3. Wiper arm and blade assembly
4. Hood weather strip
5. Roof drip moulding and front deck
garnish connection
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-22
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 54A, Column switch
.
INSTALLATION SERVICE POINTS
>>A<< WIPER BLADE INSTALLATION
CAUTION
For good windshield wiper wiping performance,
use a passenger-side windshield wiper without
an curve in the backing of the wiper blade. The
windshield wiper on the driver's side should be a
wiper blade with a curved backing.
>>B<< WIPER BLADE ASSEMBLY
INSTALLATION
Install the wiper blade at the specified position
(standard value).
Standard value:
Driver’s side (A): 35
±
5 mm
Passenger’s side (B): 25
±
5 mm
INSPECTION
M1511008000179
WINDSHIELD WIPER MOTOR CHECK
Inspect the windshield wiper motor by removing the
harness connector with the motor attached to the
vehicle.
Wiper motor at low-speed and high-speed
operation
Connect the battery to the windshield wiper motor to
inspect the operation of motor rotation in low or high
speed.
6. Front deck garnish
7. Windshield wiper motor and link
assembly
8. Link assembly
9. Windshield wiper motor assembly
Windshield wiper motor and link
assembly removal steps (Continued)
AC103612
AC
Backing
Backing
A
A
Section A – A
Wiper blade
Backing
Wiper blade
Backing
Backing
A
A
<Passenger's side>
<Driver's side>
Wiper blade
AC309409
A
B
Front deck garnish terminal
AB
AC200893
1
4
2
3
5
1
4
2
3
5
1
4
2
3
5
Check operation
Low speed
High speed
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст