Mitsubishi Outlander (2003+). Manual — part 429
GENERAL INFORMATION
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-5
Windshield wiper and washer
Intermittent control (the initial condition: with function)
ETACS-ECU calculates the intermittent time TI from
the vehicle speed calculated from the windshield
intermittent wiper volume of the column switch and
the vehicle speed signals (engine-ECU), and sends it
to the front ECU as SWS data.
NOTE: The vehicle speed sensing function can be
invalidated by the adjustment function.
The front ECU determines the intermittent time TI
from the input SWS data, and turns ON the
windshield wiper drive signal. When the wiper comes
to the stop position, the windshield wiper auto-stop
signal is turned OFF, and the windshield wiper drive
signal turns OFF.
When the intermittent time TI is elapsed after being
turned ON the windshield wiper drive signal, the
windshield wiper drive signal is turned ON again, and
the above-mentioned operation is repeated.
AC300134
Intermittent wiper volume position
FAST
AB
100
0
Intermittent time:
TI(sec.)
18
0
18
SLOW
Intermittent time:
TI(sec.)
Vehicle speed (km/h)
Intermittent wiper volume
"SLOW" position
Intermittent wiper volume
"FAST" position
AC300135
OFF
AC
TI: Intermittent time
ON
Windshield wiper auto stop signal
TI
TI
TI
OFF
ON
Windshield wiper drive signal
GENERAL INFORMATION
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-6
Mist wiper control
When the windshield wiper mist switch of the column
switch is turned ON while the ignition switch is ACC
or ON, the column switch turns ON the windshield
wiper drive signal. At the same time, the wiper speed
switching relay turns to ON (HI). When the
windshield mist wiper switch is ON, the windshield
wiper operates at the high speed.
Low speed wiper and high speed wiper control
When the windshield low speed wiper switch of the
column switch is turned ON while the ignition switch
is ACC or ON, the column switch turns ON the
windshield wiper drive signal. Also, the wiper speed
switching relay turns to OFF (LO), and the windshield
wiper operates at the low speed.
When the windshield high speed wiper switch is
turned ON, the windshield wiper drive signal turns
ON. Also, the wiper speed switching relay turns ON
(HI), and the windshield wiper operates at the high
speed.
AC300283
OFF
AC
TI: Intermittent time
ON
Windshield wiper auto stop signal
TI
TI
(LO) OFF
(HI) ON
Windshield wiper intermittent operation
Windshield wiper switch "OFF" position
Windshield wiper speed switching relay
Windshield wiper drive signal
OFF
ON
Windshield wiper "MIST" switch
OFF
ON
AC300284
OFF
AC
ON
Windshield wiper
auto stop signal
(LO) OFF
(HI) ON
Windshield wiper hight speed operation
Windshield wiper speed
switching relay
Windshield wiper
drive signal
OFF
ON
Windshield wiper "LO" switch
OFF
ON
Windshield wiper low speed operation
Windshield wiper "HI" switch
OFF
ON
GENERAL INFORMATION
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-7
Windshield wiper linked with washer function
•
When the front-ECU receives a windshield
washer switch signal from the column switch with
the ignition switch in the ACC or the ON position,
the ECU turns on the windshield washer relay.
When the windshield washer relay becomes ON,
the windshield washer motor starts to run to
spray the washer fluid in the washer tank onto the
windshield through the washer nozzles. When
the windshield washer switch signal remains on
for 0.3 seconds or more, the signal turns on the
windshield wiper relay (The wiper interval
depends. For details, see the list) to operate the
windshield wiper at high speed. Turning off the
windshield washer switch causes the front-ECU
to turn off the windshield wiper relay "T" seconds
later, thus operating the wiper to the auto stop
position at low speed.
•
When the windshield washer switch is turned ON
during the intermittent operation of the windshield
wiper, the windshield wiper switches to
continuous operation and then resumes
intermittent operation.
AC207005AD
t
t
ON
OFF
ON
OFF
ON
OFF
ON
OFF
T
T
T1
T1
Windshield wiper relay
Windshield wiper
auto stop signal
Windshield washer relay
Windshield washer switch
Wiper switch in
off position
Wiper switch in intermitent
operation position
t: 0.3 seconds
T: 3 seconds
T1: Intermittent wiper
intermittent time
Wiper
switch
OFF position
Intermittent operation position
Low-speed or
high-speed
operation
position
Washer
switch ON
time
0.3
seconds
or less
0.3 to
0.5
seconds
0.5 to
0.7
seconds
0.7
seconds
or more
0.2
seconds
or less
0.2 to
0.5
seconds
0.5 to
0.7
seconds
0.7
seconds
or more
-
T1
0
second
1
second
2
seconds
3
seconds
0
second
1
second
2
seconds
3
seconds
3 seconds
GENERAL INFORMATION
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-8
Rear wiper and washer
Rear wiper control [the initial condition: 8 seconds (without successive operations)]
1. When the rear wiper switch on the column switch
is turned ON with the ignition switch at the ACC
or ON position, ETACS-ECU turns ON the rear
wiper drive signal for 3 seconds (approximately 2
operations) and performs the intermittent action
at 8-second intervals.
When the shift lever <M/T> or selector lever <A/T> is
moved to R position during the rear wiper
operation, the back-up lamp switch <M/T> or
inhibitor switch R position <A/T> turns ON one
second after that, ETACS-ECU sends the rear
wiper drive signal for 3 seconds (approximately 2
operations), and operates the intermittent action
in 8 seconds interval.
2. By the special operation of the rear wiper switch
on the column switch (successive 2-time
operations), the rear wiper operates continuously
regardless of the set intermittent time.
NOTE: The rear wiper intermittent time can be
adjusted or canceled for continuous operation by the
adjustment function.
AC301877
OFF
AC
T2: 8.0 seconds
ON
T2
T4
Rear wiper drive signal
OFF
ON
Rear wiper switch
OFF
ON
T3
T1
Back-up lamp switch <M/T> or
inhibitor switch "R" position <A/T>
t
T1: 7.4 seconds
t: 1.0 second
T4
T3
T4
T2
T1
T2
T4
T4
T3: 3.0 seconds
T4: 0.6 second
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст