Mitsubishi Outlander (2003+). Manual — part 520
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-369
Step 4. Check the wiring harness from C-03 fog
lamp switch connector terminal No.2 <L.H. drive
vehicles> or terminal No.6 <R.H. drive vehicles>
to body earth.
•
Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 5. Connector check: C-219 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Repair the defective connector.
AC308716
AE
1
5
6
4 3 2
Connector: C-03
<LHD>
Harness side
AC308769
AE
1
5
6
4 3 2
Connector: C-03 <RHD>
Harness side
AC308722
Connector: C-219
Junction block (Rear view)
AH
68
74
63
66
72
73
67
6564
61
70
71
62
69
60
57
58
59
5655
52
54 53
51
Harness side
C-219(GR)
<LHD>
AC308776
Connector: C-219 <RHD>
Junction block (Rear view)
AE
68
74
63
66
72
73
67
6564
61
70
71
62
69
60
57
58
59
5655
52
54 53
51
Harness side
C-219(GR)
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-370
Step 6. Check the wiring harness from C-219
ETACS-ECU connector No.54 to C-03 fog lamp
switch connector terminal No.5.
•
Check the input line for open circuit.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair the wiring harness.
Step 7. Retest the system.
Check that the front fog lamp switch signal is
received normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
AC308716
AE
1
5
6
4 3 2
Connector: C-03
<LHD>
Harness side
AC308769
AE
1
5
6
4 3 2
Connector: C-03 <RHD>
Harness side
AC308722
Connector: C-219
Junction block (Rear view)
AH
68
74
63
66
72
73
67
6564
61
70
71
62
69
60
57
58
59
5655
52
54 53
51
Harness side
C-219(GR)
<LHD>
AC308776
Connector: C-219 <RHD>
Junction block (Rear view)
AE
68
74
63
66
72
73
67
6564
61
70
71
62
69
60
57
58
59
5655
52
54 53
51
Harness side
C-219(GR)
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-371
INSPECTION PROCEDURE N-16: The rear fog lamp switch signal is not received.
CAUTION
Whenever the ECU is replaced, ensure that the
input signal circuit is normal.
COMMENTS ON TROUBLE SYMPTOM
Input signal from the rear fog lamp switch is used to
operate the rear fog lamps. If the signal is abnormal,
the rear fog lamps will not illuminate and extinguish
normally.
POSSIBLE CAUSES
•
Malfunction of the fog lamp switch
•
Malfunction of the ETACS-ECU
•
Damaged harness wires and connectors
ETACS-
ECU
FOG LAMP
SWITCH
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Rear Fog Lamp Switch Input Circuit
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-372
DIAGNOSTIC PROCEDURE
Step 1. Connector check: C-03 fog lamp switch
connector
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the defective connector.
Step 2. Check the rear fog lamp switch.
Refer to GROUP 54A
−
Rear fog lamp
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Replace the fog lamp switch.
Step 3. Measure the resistance at the C-03 fog
lamp switch connector.
(1) Remove the fog lamp switch, and measure at the
wiring harness side.
(2) Continuity between C-03 fog lamp switch
connector terminal No.2 and body earth
OK: 2
Ω
or less
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 4.
AC308716
AE
1
5
6
4 3 2
Connector: C-03
<LHD>
Harness side
AC308769
AE
1
5
6
4 3 2
Connector: C-03 <RHD>
Harness side
AC308716
AE
1
5
6
4 3 2
Connector: C-03
<LHD>
Harness side
AC308769
AE
1
5
6
4 3 2
Connector: C-03 <RHD>
Harness side
AC301541 AN
Connector C-03
(Harness side)
1
5
6
4 3 2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст