Mitsubishi Outlander (2003+). Manual — part 255
TRAILING ARM ASSEMBLY
REAR SUSPENSION
34-17
TRAILING ARM BUSHING
REPLACEMENT
M1341011300209
1. Use following special tools to drive out the trailing
arm bushing.
•
MB991444: Bushing Remover and Installer Arbor
•
MB991445: Bushing Remover and Installer Base
2. Set the installation direction and installation
location of the trailing arm bushing.
(1) Place the long projection end of the trailing
arm bushing inner pipe towards the inside of
the vehicle.
(2) Make sure that the hollow of the trailing arm
bushing is located as shown in the illustration.
3. Using the special tools, press the trailing arm
bushing into the position shown.
AC102542AD
Driving Out
Trailing arm
MB991444
MB991445
AC102539 AC
Parallel
AC102542AE
Press-Fitting
MB991444
Trailing arm
MB991445
16.2 ± 0.5 mm
SHOCK ABSORBER ASSEMBLY
REAR SUSPENSION
34-18
SHOCK ABSORBER ASSEMBLY
REMOVAL AND INSTALLATION
M1341002500335
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in the unladen condition.
AC107092 AB
44 ± 5 N·m
2
4
1
3
5
95 ± 15 N·m*
95 ± 15 N·m*
39± 5 N·m
Removal steps
1.
Stabilizer link connection
<<A>>
2.
Lower arm and trailing arm
connection
3.
Shock absorber mounting nut
4.
Shock absorber and lower arm
connecting bolt
>>A<<
5.
Shock absorber assembly
Removal steps (Continued)
SHOCK ABSORBER ASSEMBLY
REAR SUSPENSION
34-19
REMOVAL SERVICE POINT
<<A>> LOWER ARM AND TRAILING ARM
DISCONNECTION
After supporting the lower arm with a jack, separate
the lower arm and trailing arm connection.
INSTALLATION SERVICE POINT
>>A<< SHOCK ABSORBER ASSEMBLY
INSTALLATION
Install the spring seat stepped section so that it
points towards the rear side of the vehicle.
INSPECTION
M1341002600149
•
Check the rubber parts for cracks and wear.
•
Check the shock absorber for malfunctions, oil
leakage, or abnormal noise.
AC107126 AB
Piece of wood
AC304795 AB
Spring seat
stepped section
Rear of
the vehicle
SHOCK ABSORBER ASSEMBLY
REAR SUSPENSION
34-20
DISASSEMBLY AND REASSEMBLY
M1341005300318
DISASSEMBLY SERVICE POINTS
<<A>> SELF-LOCKING NUT REMOVAL
CAUTION
•
To hold the coil spring securely, install
special tool arm set (MB991239) evenly, and
so that the space between both arms of the
special tool will be maximum within the
installation range.
•
Do not use an impact wrench to tighten the
bolt of special tool spring compressor body
(MB991237). It will break the special tool.
1. Use following special tools to compress the coil
spring.
•
MB991237: Spring Compressor Body
•
MB991239: Arm Set
AC209952AC
25 ± 5 N·m
1
2
4
5
3
6
7
8
9
11
13
12
10
Disassembly steps
<<A>> >>D<<
1. Self-locking nut
2. Washer
3. Upper bushing B
>>C<<
4. Bracket assembly
5. Collar
6. Upper bushing A
7. Plate
8. Bump rubber
>>A<<
9. Upper spring pad
10. Dust cover
>>B<<
11. Coil spring
>>A<<
12. Lower spring pad
<<B>>
13. Shock absorber
AC001070
MB991237
MB991239
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст