Mitsubishi Outlander (2003+). Manual — part 254
TRAILING ARM ASSEMBLY
REAR SUSPENSION
34-13
REMOVAL AND INSTALLATION <4WD>
M1341002200334
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in the unladen condition.
Pre-removal Operation
•
Brake Fluid Draining
•
Rear ABS Sensor Removal (Refer to GROUP 35B, ABS
Sensor
).
Post-installation Operation
•
Rear ABS Sensor Installation (Refer to GROUP 35B, ABS
Sensor
).
•
Brake Fluid Supplying and Bleeding (Refer to GROUP
35A, On-vehicle Service
−
Bleeding
•
Rear Wheel Alignment Check and Adjustment (Refer to
).
•
Parking Brake Lever Stroke Adjustment (Refer to GROUP
36, On-vehicle Service
−
Parking Brake Lever Stroke
Check and Adjustment
AC300347AB
90 ± 10 N·m*
120 ± 10 N·m*
95 ± 15 N·m*
7
5
9
11
6
1
15
17
8
16
2
4
120 ± 10 N·m*
15 ± 2 N·m
N
10
12
N
245 ± 29 N·m
3
63 ± 7 N·m
60 ± 5 N·m
13
39 ± 5 N·m
14
95 ± 15 N·m
Removal steps
1.
Brake hose and trailing arm
connection
2.
Parking brake cable
3.
Rear brake caliper assembly
4.
Upper arm and trailing arm
connection
5.
Lower arm and stabilizer link
connection
6.
Lower arm and shock absorber
connection
7.
Control link and trailing arm
connection
<<A>>
8.
Lower arm and trailing arm
connection
9.
Trailing arm and trailing arm
bracket connecting bolt
<<B>>
>>C<<
10. Drive shaft nut
11. Brake disc
<<C>>
•
Drive shaft connection
<<D>>
>>B<<
12. Rear hub assembly
13. Rear parking brake assembly
14. Trailing arm bracket
15. Snap ring
<<E>>
>>A<<
16. Wheel bearing
17. Trailing arm
Removal steps (Continued)
TRAILING ARM ASSEMBLY
REAR SUSPENSION
34-14
REMOVAL SERVICE POINTS
<<A>> LOWER ARM AND TRAILING ARM
DISCONNECTION
After supporting the lower arm with a jack, separate
the lower arm and trailing arm connection.
<<B>> DRIVE SHAFT NUT REMOVAL
CAUTION
Do not apply pressure to the wheel bearing by
the vehicle weight to avoid possible damage to
the wheel bearing before tightening the drive
shaft nut fully.
Use special tool end yoke holder (MB990767) to fix
the rear axle hub, and then remove the drive shaft
nut.
<<C>> DRIVE SHAFT DISCONNECTION
1. Use following special tools to push out the drive
shaft from the hub.
•
MB990241: Axle Shaft Puller
•
MB990242: Puller Shaft
•
MB990244: Puller Bar
•
MB990767: End Yoke Holder
•
MB991354: Puller Body
2. Hang the drive shaft on the vehicle body with a
rope.
CAUTION
Do not apply pressure to the wheel bearing by
the vehicle weight to avoid possible damage
when the drive shaft is removed. If, however,
vehicle weight must be applied to the bearing in
moving the vehicle, temporarily secure the wheel
bearing by using special tools front hub remover
and installer, and spacer (MB991000 and
MB991017).
AC107126 AB
Piece of wood
AC102718
MB990767
AC
AC201826
AC
MB990767
AC102719
MB991354
MB990244
(MB990241)
MB990242
(MB990241)
MB990767
AC
(Three)
AC102720
MB991000
MB991017
245 ± 29 N·m
AC
Wheel bearing
TRAILING ARM ASSEMBLY
REAR SUSPENSION
34-15
<<D>> REAR HUB ASSEMBLY REMOVAL
CAUTION
Replace the wheel bearing with a new part
because wheel bearing frictional surface will be
damaged when removing the hub.
Use following special tools to pull out the rear hub
assembly.
•
MB990211: Sliding Hammer
•
MB990241: Axle Shaft Puller
•
MB990244: Puller Bar
•
MB991354: Puller Body
<<E>> WHEEL BEARING REMOVAL
1. Use special tool bearing remover (MB990560) to
remove the wheel bearing inner race (outside)
from the rear hub assembly.
2. Use following special tools to remove the wheel
bearing from the trailing arm.
•
MB990934: Adapter
•
MB990938: Bar
INSTALLATION SERVICE POINTS
>>A<< WHEEL BEARING INSTALLATION
Use following special tools to press-in the wheel
bearing.
•
MB991400: Rear Wheel Bearing and Hub
Installer
•
MB991401: Rear Wheel Bearing and Hub
Installer Base
AC203557AC
MB990211
MB990244 (Three)
MB991354
AC103549 AC
Socket
MB990560
Rear hub
assembly
Wheel bearing
inner race
(outside)
AC103550AC
MB990938
MB990934
Trailing arm
AC103551 AC
MB991400
MB991401
Trailing arm
Wheel bearing
TRAILING ARM ASSEMBLY
REAR SUSPENSION
34-16
>>B<< REAR HUB ASSEMBLY INSTALLATION
CAUTION
If the wheel bearing inner race has been pushed
out, set the wheel bearing to the trailing arm
again before installing the rear hub assembly.
Use following special tools to press-in the rear hub
assembly.
•
MB991400: Rear Wheel Bearing and Hub
Installer
•
MB991411: Rear Wheel Bearing and Hub
Installer
>>C<< DRIVE SHAFT NUT INSTALLATION
CAUTION
Do not apply pressure to the wheel bearing by
the vehicle weight to avoid possible damage to
the wheel bearing before tightening the drive
shaft nut fully.
1. Assemble the drive shaft washer in the illustrated
direction.
2. Use special tool end yoke holder (MB990767) to
fix the rear axle hub, and the tighten the drive
shaft nut fully.
INSPECTION
M1341002300171
•
Check the bushings for wear and deterioration.
•
Check the trailing arm for bending or damage.
AC103682 AC
MB991400
MB991411
Trailing arm
Rear hub assembly
AC102721
MB990767
245 ± 29 N·m
Washer
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст