Mitsubishi Outlander (2003+). Manual — part 473
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-181
INSPECTION PROCEDURE F-7: The windshield washer does not work.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
The windshield washer motor, the column switch or
the front-ECU may be defective.
POSSIBLE CAUSES
•
Malfunction of the windshield washer motor
•
Malfunction of the column switch
•
Malfunction of the front-ECU
•
Damaged harness wires and connectors
30
25
22
21
2324
2627
29
28
31
2
1
W3Z04E04A
OFF
ON
20A
J/B
7
5
9
18
28
31
1
2
C-116
C-202
C-203
A-26
L-Y
L-B
L-B
LG
B
A-12X
FRONT-ECU
WINDSHIELD
WASHER MOTOR
WINDSHIELD
WASHER
RELAY
INPUT SIGNAL
WINDSHIELD WASHER
IGNITION
SWITCH (ACC)
Wire colour code
B : Black LG : Light green G : Green L : Blue
W : White Y : Yellow SB : Sky blue BR : Brown
O : Orange GR : Gray R : Red P : Pink V : Violet
Windshield Washer Motor Circuit
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-182
DIAGNOSIS PROCEDURE
Step 1. Check the operation of the windshield
wipers.
Check that the windshield wipers work normally.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Refer to Inspection Procedure F-1 "The
windshield wipers does not work at all
Step 2. Pulse check
Check the input signals below which are related to
the windshield wiper.
OK: The MUT-II/III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
All the signals are received normally :
Go to Step
The ignition switch (ACC) signal is not received. :
Refer to inspection procedure N-1 "The
ignition switch (ACC) signal is not received
Windshield washer switch signal is not received. :
Refer to inspection procedure N-6 "The
column switch (windshield wiper washer
and rear wiper washer switch) signal is not
received
Step 3. Connector check: A-26 windshield
washer motor connector
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the connector.
Step 4. Check the windshield washer motor
assembly.
Refer to GROUP 51
−
Windshield washer
Q: Is the check result normal?
YES :
Go to Step 5
NO :
Replace the windshield washer motor.
System switch
Check condition
Ignition switch (ACC)
When turned from the
LOCK (OFF) position to
the ACC position.
Windshield washer
switch
When the switch is
turned from off to on.
AC308677
2
1
AF
Connector: A-26
<LHD>
Harness side
AC308684
2
1
AH
Connector: A-26
<RHD>
Harness side
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-183
Step 5. Measure the resistance at the A-26
windshield washer motor connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Continuity between A-26 windshield washer
motor connector terminal No.1 and body earth
OK: 2
Ω
or less
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Go to Step 6.
Step 6. Check the wiring harness between A-26
windshield washer motor connector terminal
No.1 and body earth.
•
Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 7. Connector check: A-12X front-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Repair the connector.
AC308677
2
1
AF
Connector: A-26
<LHD>
Harness side
AC308684
2
1
AH
Connector: A-26
<RHD>
Harness side
2
1
AC301475
Connector A-26
(Harness side)
AB
AC308677
2
1
AF
Connector: A-26
<LHD>
Harness side
AC308684
2
1
AH
Connector: A-26
<RHD>
Harness side
AC301515 AE
Connector: A-12X
24
29
30
31
2827
25
26
21
2322
Relay box side
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-184
Step 8. Check the wiring harness between A-26
windshield washer motor connector terminal
No.2 and A-12X front-ECU connector terminal
No.31.
•
Check the power supply line to the ignition switch
(ACC) for open circuit.
Q: Is the check result normal?
YES :
Go to Step 9.
NO :
Repair the wiring harness.
Step 9. Retest the system.
The windshield washer should now work normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Replace the front-ECU.
AC301515 AE
Connector: A-12X
24
29
30
31
2827
25
26
21
2322
Relay box side
AC308677
2
1
AF
Connector: A-26
<LHD>
Harness side
AC308684
2
1
AH
Connector: A-26
<RHD>
Harness side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст