Mitsubishi Outlander (2003+). Manual — part 475
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-189
NOTE:
Prior to the wiring harness inspection, check
intermediate connector F-05 and junction block
connectors C-209 <L.H. drive vehicles> and C-211
<R.H. drive vehicles>, and repair if necessary.
•
Check the output line.
Q: 1Is the check result normal?
YES :
Go to Step 9.
NO :
Repair the wiring harness.
Step 9. Retest the system.
Check that the rear wiper works normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
AC308720
Connector: C-209
<LHD>
Harness side
AH
7
15
5
6
1413
2
9
12
4 3
10
11
1
8
Junction block (Front view)
AC308772
Harness side
AK
7
15
5
6
1413
2
9
12
4 3
10
11
1
8
Junction block (Front view)
Connector: C-211
<RHD>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-190
INSPECTION PROCEDURE G-2: The rear wiper does not stop at the specified park position.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
IGNITION
SWITCH (ACC)
REAR
WIPER
RELAY
REAR WIPER
MOTOR
ETACS-
ECU
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Rear Wiper Auto-stop Signal Input <LHD>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-191
COMMENTS ON TROUBLE SYMPTOM
If the rear wiper does not stop normally within the
predetermined range, the rear wiper motor or the
ETACS-ECU may be defective.
POSSIBLE CAUSES
•
Malfunction of the rear wiper motor
•
Malfunction of the ETACS-ECU
•
Damaged harness wires and connectors
Step 1. Connector check: F-02 rear wiper motor
connector
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the connector.
IGNITION
SWITCH(ACC)
ETACS-
ECU
REAR
WIPER
RELAY
REAR WIPER
MOTOR
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Rear Wiper Auto-stop Signal Input <RHD>
AC308808
Connector: F-02
AG
Harness side
3
4
2 1
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-192
Step 2. Check the rear wiper motor.
Refer to GROUP 51
−
Rear wiper and washer
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Replace the rear wiper motor.
Step 3. Measure the voltage at the F-02 rear wiper
motor connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Ignition switch: ACC
(3) Check the voltage between F-02 rear wiper motor
connector terminal No.4 and body earth
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 4.
Step 4. Check the wiring harness between
ignition switch (ACC) and F-02 rear wiper motor
connector terminal No.4.
AC308808
Connector: F-02
AG
Harness side
3
4
2 1
3
4
2 1
AC301642
Connector F-02
(Harness side)
AB
AC308808
Connector: F-02
AG
Harness side
3
4
2 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст