Mitsubishi Outlander (2003+). Manual — part 499
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-285
NOTE:
Prior to the wiring harness inspection, check junction
block connector C-210, and repair if necessary.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair the wiring harness.
Step 7. Check the wiring harness from C-217
ETACS-ECU connector terminal Nos. 5 and 6 to
D-11 rear room lamp connector terminal Nos. 2
and 1.
AC308720
Connector: C-210
Harness side
AK
3
1
2
Junction block (Front view)
<LHD>
AC308772
Connector: C-210
Harness side
AJ
3
1
2
Junction block (Front view)
<RHD>
AC308722
Connector: C-217
Junction block (Rear view)
Junction block side
AD
3
1
2
14
4
5
7 6
8
1110 9
1312
17
15
16
18
19
20
<LHD>
AC308776
Connector: C-217
Junction block (Rear view)
Junction block side
AC
3
1
2
14
4
5
7 6
8
1110 9
1312
17
15
16
18
19
20
<RHD>
AC308783
Connector: D-11
AE
Harness side
2 1
D-11(GR)
<LHD>
AC308787
Connector: D-11
AD
Harness side
2 1
D-11(GR)
<RHD>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-286
NOTE:
Prior to the wiring harness inspection, check junction
block connector C-210, and repair if necessary.
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Repair the wiring harness.
Step 8. Retest the system.
Check that the front or rear room lamp illuminates
and extinguishes normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
AC308720
Connector: C-210
Harness side
AK
3
1
2
Junction block (Front view)
<LHD>
AC308772
Connector: C-210
Harness side
AJ
3
1
2
Junction block (Front view)
<RHD>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-287
INSPECTION PROCEDURE M-2: The front and rear room lamp do not illuminate or extinguish
normally. <Vehicles with keyless entry system>
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
The ETACS-ECU operates this function in
accordance with the input signals below.
•
Ignition switch (IG1)
•
Key reminder switch
•
All of the door switches
•
Driver's door lock actuator
•
Interior lamp loaded signal
If this function does not work normally, these input
signal circuit(s), the interior lamp
automatic-shutdown function or the ETACS-ECU
may be defective. The delay-off setting of this
function can be changed by the adjustment function
(default setting; 15 seconds).
POSSIBLE CAUSES
•
Malfunction of the key reminder switch
•
Malfunction of the door switches
•
Malfunction of the driver's door lock actuator
•
Malfunction of the ETACS-ECU
•
Damaged harness wires and connectors
ETACS-ECU
REAR
ROOM
LAMP
FRONT
ROOM
LAMP
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Room Lamp Circuit
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-288
DIAGNOSTIC PROCEDURE
Step 1. Check the adjustment function.
Check that the room lamp delay-off time has been
set to other than "0 second" by the adjustment
function.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Use the adjustment function to set the room
lamp delay-off time to other than "0 second."
Refer to
Step 2. Check the power supply circuit.
When the ignition switch is turned to the LOCK
(OFF) position, check if the hazard warning lamps
illuminate.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Refer to inspection procedure A-2 "Check
the ETACS-ECU battery power supply
circuit"
.
Step 3. Pulse check
Check the input signals below, which are related to
the front and rear room lamps.
OK: The MUT-II/III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
All the signals are received normally. :
Go to Step
The ignition switch (IG1) signal is not received. :
Refer to inspection procedure N-2 "The
ignition switch (IG1) signal is not received
All the door switch signals are not received. :
Refer to inspection procedure N-11 "All the
door switch signals are not received <L.H.
drive vehicles>
vehicles>
The driver's door lock actuator switch signal is not
received. :
Refer to inspection procedure N-12
"The driver's door lock actuator switch
signal is not received <L.H. drive
vehicles>
vehicles>
Interior lamp loaded signal is not detected. :
Refer
to inspection procedure N-17 "Interior lamp
loaded signal is not detected
System switch
Check condition
Ignition switch (IG1)
When turned from ACC
to ON
All of the door switches
A door is opened when
all the doors are closed
Driver's door lock
actuator switch
When the driver's door is
unlocked or locked
Interior lamp loaded
signal
When a load is applied
through multi-purpose
fuse No.22
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст