Mitsubishi Outlander (2003+). Manual — part 245

ENGINE ROLL STOPPER, CENTREMEMBER <4G63>

POWER PLANT MOUNT

32-11

INSTALLATION SERVICE POINT

>>A<< ENGINE ROLL STOPPER BRACKET
INSTALLATION

Install the engine roll stopper bracket so that its hole
points towards the front side of the vehicle.

INSPECTION

M1321002400057

•

Check the roll stopper for cracks, separation or
deformation.

•

Check the centremember for cracks or damage.

Engine roll stopper rod and
bracket removal steps <4WD>

•

Front exhaust pipe (Refer to
GROUP 15, Exhaust pipe

P.15-13

).

5.

Engine roll stopper rod connecting
bolt

11. Engine roll stopper rod assembly
12. Engine roll stopper rod bracket and

crossmember assembly (Refer to

P.32-14

).

13. Engine roll stopper rod bracket
14. Crossmember assembly

AC208360

Front of vehicle

Hole

AC

ENGINE ROLL STOPPER, CENTREMEMBER <4G69>

POWER PLANT MOUNT

32-12

ENGINE ROLL STOPPER, CENTREMEMBER <4G69>

REMOVAL AND INSTALLATION

M1321002300340

CAUTION

*: Indicates parts which should be initially tightened, and then fully tightened after placing the vehicle
horizontally and loading the full weight of the engine on the vehicle body.

AC309432

45 ± 5 N·m

52 ± 7 N·m

5

<R.H. drive vehicles>

45 ± 5 N·m

52 ± 7 N·m

52 ± 7 N·m

10

<L.H. drive vehicles>

45 ± 5 N·m

52 ± 7 N·m

3

4

1

2

69 ± 10 N·m

69 ± 10 N·m

AB

45 ± 5 N·m

3 4

2

<M/T>

<A/T>

9

52 ± 7 N·m

1

8

7

6

13

12

11

Front roll stopper and
centermember removal steps

•

Under cover (Refer to GROUP 51,
Under cover

P.51-19

).

1.

Engine roll stopper bracket
connecting bolt

2.

Centremember and engine roll
stopper bracket assembly

3.

Centremember

>>A<<

4.

Engine roll stopper bracket

Engine rear roll stopper bracket
removal steps <R.H. drive
vehicles>

•

Front exhaust pipe (Refer to
GROUP 15, Exhaust pipe

P.15-13

).

5.

Engine rear roll stopper bracket
connecting bolt

6.

Engine rear roll stopper bracket
and crossmember assembly (Refer
to

P.32-14

).

ENGINE ROLL STOPPER, CENTREMEMBER <4G69>

POWER PLANT MOUNT

32-13

INSTALLATION SERVICE POINT

>>A<< ENGINE ROLL STOPPER BRACKET
INSTALLATION

Install the engine roll stopper bracket so that its hole
points towards the front side of the vehicle.

INSPECTION

M1321002400068

•

Check the roll stopper for cracks, separation or
deformation.

•

Check the centremember for cracks or damage.

7.

Engine rear roll stopper bracket

8.

Crossmember assembly
Engine roll stopper rod and
bracket removal steps <L.H.
drive vehicles>

•

Front exhaust pipe (Refer to
GROUP 15, Exhaust pipe

P.15-13

).

9.

Engine roll stopper rod connecting
bolt

10. Engine roll stopper rod assembly
11. Engine roll stopper rod bracket and

crossmember assembly (Refer to

P.32-14

).

12. Engine roll stopper rod bracket
13. Crossmember assembly

Engine rear roll stopper bracket
removal steps <R.H. drive
vehicles> (Continued)

AC208360

AC101615

AC309431

Front of vehicle

Hole

AB

Front of vehicle

Hole

<M/T>

<A/T>

CROSSMEMBER

POWER PLANT MOUNT

32-14

CROSSMEMBER

REMOVAL AND INSTALLATION

M1321003200410

CAUTION

•

Before removing the steering wheel and air bag module assembly, always refer to GROUP 52B -
Service Precautions, Air bag Module and Clock Spring. Also, set the front wheels so that they are
facing straight forward, and remove the ignition key. If you fail to do this, the SRS clock spring will
be damaged, causing the SRS air bag to be inoperative and serious injury.

•

*

1

: Indicates parts which should be initially tightened, and then fully tightened after placing the

vehicle horizontally and loading the full weight of the engine on the vehicle body.

•

*

2

: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle

on the earth in the unladen condition.

Pre-removal Operation

•

Steering Wheel Air Bag Module Assembly Removal

(Refer to GROUP 37, Steering Wheel

P.37A-16

).

•

Power Steering Fluid Draining (Refer to GROUP 37A,

On-vehicle Service

P.37A-11

).

•

Front Exhaust Pipe Removal (Refer to GROUP 15,

Exhaust Pipe and Main Muffler

P.15-13

).

•

Centremember Removal (4G63: Refer to

P.32-10

),

(4G69: Refer to

P.32-12

).

Post-installation Operation

•

Centremember Installation (4G63: Refer to

P.32-10

),

(4G69: Refer to

P.32-12

).

•

Front Exhaust Pipe Installation (Refer to GROUP 15,

Exhaust Pipe and Main Muffler

P.15-13

).

•

Steering Wheel Air Bag Module Assembly Installation

(Refer to 37, Steering Wheel

P.37A-16

).

•

Power Steering Fluid Supplying (Refer to GROUP 37A,

On-vehicle Service

P.37A-11

).

•

Power Steering Fluid Line Bleeding (Refer to GROUP

37A, On-vehicle Service

P.37A-12

).

•

Press the dust cover with a finger to check whether the
dust cover cracked or damaged.

•

Checking Steering Wheel Position with Wheels Straight

Ahead.

•

Front Wheel Alignment Check and Adjustment (Refer to

GROUP 37A, On-vehicle Service

P.37A-9

).