Mitsubishi Outlander (2003+). Manual — part 114
THROTTLE BODY ASSEMBLY
MULTIPORT FUEL INJECTION (MFI)
13A-319
2. Turn the fuel injector assembly. To the right and
left to install to the fuel delivery pipe. Repeat for
delivery pipe pressure regulator and fuel high-
pressure hose. Be careful not to damage the O-
ring. After installing, check that the item turns
smoothly.
3. If it dose not turn smoothly, the O-ring may be
trapped, remove the item, re-install it into the fuel
delivery pipe and check again.
4. Tighten the delivery pipe pressure regulator and
fuel high-pressure hose to the specified torque.
Tightening torque:
8.9
1.9 N
¼
m <Delivery pipe pressure regula-
tor>
5.0
1.0 N
¼
m <Fuel high-pressure hose>
THROTTLE BODY ASSEMBLY
REMOVAL AND INSTALLATION
M1131007700544
Pre-removal Operation
Engine Coolant Draining (Refer to GROUP 14, On-vehicle
Service
-
Engine Coolant Replacement
).
Air Cleaner Removal (Refer to GROUP 15, Air Cleaner
).
Post-installation Operation
Air Cleaner Installation (Refer to GROUP 15, Air Cleaner
Engine Coolant Supplying (Refer to GROUP 14, On-vehi-
cle Service
-
Engine Coolant Replacement
Accelerator Cable Adjustment (Refer to GROUP 17, On-
vehicle Service
-
Accelerator Cable Adjustment
AC300416AB
2
8
3
4
5
6
7
1
5.0 ± 1.0 N·m
19 ± 3 N·m
N
Removal steps
1.
Accelerator cable connection
2.
Throttle position sensor connector
3.
Idle speed control servo connector
4.
Water return hose connection
5.
Water feed hose connection
6.
Emission vacuum hose
connection
7.
Throttle body assembly
>>A<<
8.
Throttle body gasket
Removal steps
&RQWLQXHG
THROTTLE BODY ASSEMBLY
MULTIPORT FUEL INJECTION (MFI)
13A-320
INSTALLATION SERVICE POINT
>>A<< THROTTLE BODY GASKET INSTALLA-
TION
CAUTION
Poor idling etc. may result if the throttle body
gasket is installed incorrectly.
Install the throttle body gasket as shown in the illus-
tration.
THROTTLE BODY ASSEMBLY DISASSEMBLY AND REASSEMBLY
M1131009700409
AC200313AB
Towards front
of vehicle
Up
AK203824 AB
4
1
5
3
2
2.0 ± 0.5 N·m
2.0 ± 0.5 N·m
6
Removal steps
<<A>>
>>A<<
1. Throttle position sensor
2. Idle speed control servo
3. O-ring
<<B>>
4. Throttle body
5. Speed adjusting screw
6. O-ring
Removal steps
&RQWLQXHG
THROTTLE BODY ASSEMBLY
MULTIPORT FUEL INJECTION (MFI)
13A-321
NOTE:
.
The speed adjusting screw is correctly adjusted
at the factory and should not be removed.
If the speed adjusting screw should happen to
have been removed, carry out speed adjusting
screw adjutment.
DISASSEMBLY SERVICE POINTS
<<A>> THROTTLE POSITION SENSOR DISASSE-
BLY
1. Do not disassemble the sensor and motor.
2. Do not clean the sensor and motor by dipping
them into cleaning solvent. Clean them with shop
towel.
<<B>> THROTTLE BODY DISASSEMBLY
1. Do not disassemble the throttle body.
2. Check if the vacuum port or passage is clogged.
Use compressed air to clean the vacuum
passage.
REASSEMBLY SERVICE POINT
>>A<< THROTTLE POSITION SENSOR (TPS)
INSTALLATION
1. Install the throttle position sensor to the throttle
body as shown in the illustration.
2. Turn the throttle position sensor 90 degrees
counterclockwise to set it, and tighten the screws.
3. Connect an ohmmeter between terminals 2
(output) and 4 (earth), or between terminals 1
(power) and 2 (output).
Then, make sure that the resistance changes
smoothly when the throttle valve is slowly moved
to the fully open position.
AK203835 AB
AK200203
Throttle position
sensor power
AB
Throttle position
sensor output
Earth
ENGINE ECU
MULTIPORT FUEL INJECTION (MFI)
13A-322
ENGINE ECU
REMOVAL AND INSTALLATION
M1131033800036
Pre-removal and Post-installation Operation
Cowl Side Trim (RH) Removal and Installation (Refer to
GROUP 52A, Instrument Panel Assembly
AC300630AB
1
5.0 ± 1.0 N·m
3
2
5.0 ± 1.0 N·m
REMOVAL STEPS
1.
Engine-ECU connector
2.
Engine-ECU
3.
Engine-ECU bracket
REMOVAL STEPS
&RQWLQXHG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст