Mitsubishi Outlander (2003+). Manual — part 303
POWER STEERING GEAR BOX AND LINKAGE
POWER STEERING
37A-35
TIE ROD END BALL JOINT DUST COVER
REPLACEMENT
M1372008200383
If the dust cover is damaged accidentally during
service work, replace the dust cover as follows:
1. Apply specified grease to the lip and inside of the
dust cover.
Specified grease:
Multipurpose grease SAE J310, NLGI No.2 or
equivalent
2. Drive in the dust cover with special tool front axle
base (MB990776) until it is fully seated.
3. Check the dust cover for cracks or damage by
pushing it with your finger.
AC001012AB
MB990776
POWER STEERING OIL PUMP ASSEMBLY
POWER STEERING
37A-36
POWER STEERING OIL PUMP ASSEMBLY
REMOVAL AND INSTALLATION
M1372005200395
<2000>
Pre-removal Operation
•
Front Under Cover (RH) and Side Under Cover (RH)
Removal (Refer to GROUP 51, Under Cover
•
Power Steering Fluid Draining (Refer to
).
Post-installation Operation
•
Power Steering Fluid Supplying and Bleeding (Refer to
•
Drive Belt Tension Check (Refer to GROUP 11A,
On-vehicle Service
−
Drive Belt Tension Check
<2000>, Refer to GROUP 13A, On-vehicle Service - Drive
Belt Tensioner
<2400>).
•
Front Under Cover (RH) and Side Under Cover (RH)
Installation (Refer to GROUP 51, Under Cover
AC200116 AB
22 ± 4 N·m
12 ± 2 N·m
22 ± 4 N·m
49 ± 9 N·m
57 ± 7 N·m
1
5
4
3
6
2
7
49 ± 9 N·m
Removal steps
1.
Pressure switch connector
2.
Drive belt (Refer to GROUP 11A,
Engine assembly
.)
>>A<<
3.
Suction hose
4.
Pressure hose
<<A>>
5.
Oil pump assembly
6.
A/C compressor harness
7.
Power steering pump bracket
Removal steps (Continued)
POWER STEERING OIL PUMP ASSEMBLY
POWER STEERING
37A-37
<2400>
REMOVAL SERVICE POINT
<<A>> OIL PUMP ASSEMBLY REMOVAL
With the engine lifted by the jack, remove the oil
pump assembly mounting bolt (lower side) at the
pulley side.
AC305528
6
7
9
8
13 ± 1 N·m
7
24 ± 4 N·m
24 ± 2 N·m
44 ± 10 N·m
24 ± 2 N·m
12
11
10
1
3
4
57 ± 7 N·m
2
5
AD
(Engine oil)
N
N
REMOVAL STEPS
1.
Drive belt (Refer to GROUP 11C,
Engine assembly
>>A<<
2.
Suction hose
3.
Pressure switch connector
4.
Pressure hose
5.
Power steering oil pressure sensor
harness clamp
6.
Control wiring harness clamp
7.
Battery wiring harness clamp
8.
Engine oil dipstick and dipstick guide
9.
O-ring
10.
Oil pump and bracket assembly
11.
Bracket
<<A>>
12.
Oil pump assembly
REMOVAL STEPS (Continued)
POWER STEERING OIL PUMP ASSEMBLY
POWER STEERING
37A-38
INSTALLATION SERVICE POINT
>>A<< SUCTION HOSE INSTALLATION
Install the suction hose so that the marking is
positioned as shown in the illustration.
INSPECTION
M1372005300240
•
Check the drive belt for cracks.
•
Check the pulley for uneven rotation.
AC103338
AD
Suction hose
<2000>
AC302812
Suction hose
Oil pump
AE
<2400>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст