Mitsubishi Outlander (2003+). Manual — part 328
RADIATOR GRILLE
EXTERIOR
51-11
REMOVAL SERVICE POINT
<<A>> CLIPS REMOVAL
To remove the clips from the radiator grille, gently
pull forward the radiator grille, and use a flat-tipped
screwdriver to hold the claw of the clip in the
direction of the arrow.
INSTALLATION SERVICE POINT
>>A<< RADIATOR GRILLE INSTALLATION
Install the radiator grille with the clips installed.
AC309411
Claw
Clip
Section A – A
AB
A
Radiator grille
Radiator grille
Front bumper
assembly
A
Flat-tipped screwdriver
A
A
GARNISHES
EXTERIOR
51-12
GARNISHES
ADHESIVE
M1511000500352
SPECIAL TOOL
M1511000600995
GARNISHES
GARNISH REMOVAL AND INSTALLATION
M1511004100141
Application
Brand
Side sill garnish
Double-sided tape [5.0 mm width 0.8 mm thickness,
5.0 width 1.2mm thickness]
Tool
Number
Name
Application
MB990784
Ornament remover
Removal of side sill garnish
MB990784
AC301940
B
A
AB
A
B
1
Clip
Clip
1
Splash
shield
Section A – A
Section B – B
1
Removal steps
•
Front deck garnish (Refer to
).
<<A>> >>A<<
1. Side sill garnish
GARNISHES
EXTERIOR
51-13
DOUBLE-SIDED TAPE AFFIXED
LOCATION
REMOVAL SERVICE POINT
<<A>> SIDE SILL GARNISH REMOVAL
Gently lift and remove the side sill garnish. If there is
any double-sided tape remaining on the side sill
garnish, remove according to the following
instructions.
<Remove both-side tape remaining on the body
surface>
1. Attach protection tape all the way along the edges
of the double-sided tape which is still adhering to
the body.
2. Scrape off the double-sided tape with a resin
spatula as possible.
3. Peel off the protection tape.
4. Wipe the body surface and clean it with a rag
moistened with isopropyl alcohol.
AC107438
AC107438AB
A
B
Side sill garnish
Double-sided tape: Generic products
A : 5.0 mm width, 0.8 mm thickness, B : 5.0 mm width, 1.2 mm thickness
B
AC200049
AB
Protection tape
Double-sided tape
AC200050
AB
Double-sided tape
GARNISHES
EXTERIOR
51-14
<Remove double-sided tape remaining on side
sill garnish and adhere double-sided tape (when
re-using side sill garnish)>
1. Scrape off the double-sided tape on the side sill
garnish with a resin spatula as possible.
2. Wipe the side sill garnish surface and clean it with
a rag moistened with isopropyl alcohol.
3. Remove only a small portion of the residual
adhesive.
4. Adhere the double-sided tape as specified on the
side sill garnish (Refer to double-sided tape
adherence location).
INSTALLATION SERVICE POINT
>>A<< SIDE SILL GARNISH INSTALLATION.
1. Tear off the double-sided tape backing paper.
NOTE: If you attach the adhesive tape to the edge
of the backing paper, it will be easy to tear off.
2. Install the side sill garnish.
NOTE: If the double-sided tape is difficult to affix
in cold temperature, etc., warm the bonding
surfaces of the body and side sill garnish to about
40
−
60
°
C before affixing the tape.
3. Firmly press in the side sill garnish.
AC103187
AC103247
Backing paper
Adhesive tape
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст