Mitsubishi Outlander (2003+). Manual — part 410
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-35
REMOVAL SERVICE POINT
<<A>> STEERING LOCK CYLINDER REMOVAL
1. Insert the key in the steering lock cylinder and turn
it to the "ACC" position.
2. Using a small Phillips head screwdriver, pull the
steering lock cylinder toward you.
INSPECTION
M1544009700247
IGNITION SWITCH CONTINUITY CHECK
Disconnect ignition switch connector C-303 without
removing the ignition switch. Then check the
continuity.
KEY REMINDER SWITCH CONTINUITY
CHECK
Disconnect key reminder switch connector C-304
without removing the ignition switch and key
reminder switch. Then check the continuity.
5. Clock spring and column switch
assembly (Refer to GROUP 52B, Air
bag modules and clock spring
<<A>>
6. Steering lock cylinder
•
Ignition switch connector
7. Ignition switch
•
Key reminder switch connector
8. Key reminder switch and bulb
assembly
9. Immobilizer-ECU
Removal steps (Continued)
AC200314
AB
Lock pin
AC200316
AB
3
6
1
4 5
2
Switch
position
Tester
connection
Specified
condition
"LOCK" (OFF)
1
−
2, 1
−
3, 1
−
4, 1
−
5, 1
−
6, 2
−
3, 2
−
4, 2
−
5,
2
−
6, 3
−
4, 3
−
5, 3
−
6, 4
−
5, 4
−
6, 5
−
6
Open circuit
"ACC"
1
−
6
Less than 2
ohms
"ON"
1
−
2, 1
−
4, 1
−
6, 2
−
4, 2
−
6, 4
−
6
Less than 2
ohms
"START"
1
−
2, 1
−
5, 2
−
5
Less than 2
ohms
Status of
ignition key
Tester
connection
Specified
condition
Removed
4
−
6
Less than 2
ohms
Inserted
4
−
6
Open circuit
AC200315
1
3
2
7
6
5
4
AB
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL
54A-36
COMBINATION METER ASSEMBLY
SERVICE SPECIFICATIONS
M1543000300379
SEALANT
M1543024600039
Item
Standard value
Speedometer indication error km/h (mph)
20 (12)
20
−
24 (12
−
15)
40 (25)
40
−
44 (25
−
28)
80 (50)
80
−
86 (50
−
53)
120 (75)
122
−
128 (75
−
79)
160 (100)
163
−
170 (100
−
105)
200 (125)
204
−
212 (126
−
131)
Tachometer indication error r/min
700
700
±
100
2,000
2,000
±
100
3,000
3,000
±
150
4,000
4,000
±
200
5,000
5,000
±
250
6,250
6,250
±
150
Fuel gauge unit
resistance
Ω
2WD
Float position F (highest) 3.0
±
0.6
Float position E (lowest) 110
±
2.5
4WD
Fuel pump and
gauge unit
Float position F (highest) 1.5
±
0.5
Float position E (lowest) 55
±
1.5
Fuel gauge unit
Float position F (highest) 1.5
±
0.5
Float position E (lowest) 55
±
1.5
Fuel gauge unit float
height mm
2WD
Float position F (A)
35.4
±
2
Float position E (B)
186.7
±
2
4WD
Fuel pump and
gauge unit
Float position F (At)
36.7
±
2
Float position E (B)
149.6
±
2
Fuel gauge unit
Float position F (A)
23.4
±
2
Float position E (B)
194.2
±
2
Engine coolant temperature gauge unit resistance
Ω
104 + 13.5 (at 70
°
C)
Item
Specified sealant
Engine coolant temperature gauge unit
3M 1215 or equivalent
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL
54A-37
SPECIAL TOOLS
M1543000601908
Tool
Number
Name
Use
MB990784
Ornament remover
Removal of instrument panel
driver’s side garnish and
meter bezel.
MB991502
MUT-II sub assembly
Reading MPI system
diagnosis code
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991825
F: MB991826
MUT-III sub assembly
A: Vehicle
communication
interface (V.C.I.)
B: MUT-III USB cable
C: MUT-III main
harness A (Vehicles
with CAN
communication
system)
D: MUT-III main
harness B (Vehicles
without CAN
communication
system)
E:MUT-III
measurement
adapter harness
F: MUT-III trigger
harness
Reading MPI system
diagnosis code
CAUTION
MUT-III main harness B
(MB991911) should be
used. MUT-III main harness
A and C should not be used
for this vehicle.
MB990784
B991502
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
A
B
C
D
E
F
DO NOT USED
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL
54A-38
TROUBLESHOOTING
SYMPTOM CHART
M1543007201202
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Test harness
B: LED harness
C: LED harness
adapter
D: Probe
Making voltage and
resistance measurements
during troubleshooting
A: Connect pin contact
pressure inspection
B: Power circuit inspection
C: Power circuit inspection
D: Commercial tester
connection
Tool
Number
Name
Use
MB991223
A
B
C
D
AC
Symptom
Inspection
procedure No.
Reference page
Speedometer does not work (the other meters work) <M/T>.
1
Speedometer does not work (the other meters work) <A/T>.
2
Tachometer does not work (the other meters work).
3
Fuel gauge does not work (the other meters work).
4
Engine coolant temperature gauge does not work (the other
meters work).
5
Combination meters does not work (the instruments do not
work).
6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст