Mitsubishi Outlander (2003+). Manual — part 470
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-169
NOTE:
Prior to the wiring harness inspection, check the
intermediate connector A-14 and repair if necessary.
•
Check the input signal lines.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair the wiring harness.
Step 7. Retest the system.
Check that the windshield wipers stop at the
specified park position.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Replace the front-ECU.
AC308679 AB
Connector: A-14
A-14 (GR)
<LHD>
AC308686AB
Connector: A-14
A-14 (GR)
<RHD>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-170
INSPECTION PROCEDURE F-4: The windshield wipers does not work normally.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
Wire colour code
B : Black LG : Light green G : Green L : Blue
W : White Y : Yellow SB : Sky blue BR : Brown
O : Orange GR : Gray R : Red P : Pink V : Violet
WINDSHIELD
WIPER MOTOR
CIRCUIT
BREAKER
WINDSHIELD
WIPER MOTOR
FRONT-ECU
INPUT SIGNAL
· WINDSHIELD WIPER HI SPEED SWITCH
· WINDSHIELD WIPER INTERMIT SWITCH
· WINDSHIELD WIPER LO SPEED SWITCH
· WINDSHIELD WIPER MIST SWITCH
WIPER SPEED
SWITCHING
RELAY
Windshield Wiper Motor Drive Circuit <LHD>
Wire colour code
B : Black LG : Light green G : Green L : Blue
W : White Y : Yellow SB : Sky blue BR : Brown
O : Orange GR : Gray R : Red P : Pink V : Violet
WINDSHIELD
WIPER MOTOR
FRONT-ECU
INPUT SIGNAL
· WINDSHIELD WIPER HI SPEED SWITCH
· WINDSHIELD WIPER INTERMIT SWITCH
· WINDSHIELD WIPER LO SPEED SWITCH
· WINDSHIELD WIPER MIST SWITCH
WIPER SPEED
SWITCHING
RELAY
CIRCUIT
BREAKER
Windshield Wiper Motor Drive Circuit <RHD>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-171
COMMENTS ON TROUBLE SYMPTOM
The windshield wiper motor, the column switch or the
front-ECU may be defective.
POSSIBLE CAUSES
•
Malfunction of the windshield wiper motor
•
Malfunction of the column switch
•
Malfunction of the front-ECU
•
Damaged harness wires and connectors
Step 1. Pulse check
Check the input signals below which are related to
the windshield wiper.
OK: The MUT-II/III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
All the signals are received normally :
Go to Step
The ignition switch (ACC) signal is not received. :
Refer to inspection procedure N-1 "The
ignition switch (ACC) signal is not received
Windshield mist wiper switch signal is not
received. :
Refer to inspection procedure N-6 "The
column switch (windshield wiper washer
and rear wiper washer switch) signal is not
received
."
Windshield intermittent wiper switch signal is not
received. :
Refer to inspection procedure N-6 "The
column switch (windshield wiper washer
and rear wiper washer switch) signal is not
received
."
Windshield low-speed wiper switch signal is not
received. :
Refer to inspection procedure N-6 "The
column switch (windshield wiper washer
and rear wiper washer switch) signal is not
received
."
Windshield high-speed wiper switch signal is not
received. :
Refer to inspection procedure N-6 "The
column switch (windshield wiper washer
and rear wiper washer switch) signal is not
received
."
Step 2. Check the operation of the windshield
wipers.
Check that the windshield wipers work at high speed
and the mist mode.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Go to Step 9.
System switch
Check condition
Ignition switch (ACC)
When turned from the
LOCK (OFF) position to
the ACC position.
Windshield mist wiper
switch
When the switch is
turned from off to on.
Windshield intermittent
wiper switch
When the switch is
turned from off to on.
Windshield low-speed
wiper switch
When the switch is
turned from off to on.
Windshield high-speed
wiper switch
When the switch is
turned from off to on.
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-172
Step 3. Connector check: B-07 windshield wiper
motor connector
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the defective connector.
Step 4. Measure the voltage at the B-07
windshield wiper motor connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Ignition switch: ON
(3) Windshield wiper switch: LO
AC308694
Connector: B-07 <2000>
B-07(GR)
AE
Harness side
4
1
2
5
3
AC308708
Connector: B-07 <2400 LHD>
B-07(GR)
AF
Harness side
4
1
2
5
3
AC308710
Connector: B-07
<2400 RHD>
B-07(GR)
AB
Harness side
4
1
2
5
3
AC308694
Connector: B-07 <2000>
B-07(GR)
AE
Harness side
4
1
2
5
3
AC308708
Connector: B-07 <2400 LHD>
B-07(GR)
AF
Harness side
4
1
2
5
3
AC308710
Connector: B-07
<2400 RHD>
B-07(GR)
AB
Harness side
4
1
2
5
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст