Mitsubishi Grandis. Manual — part 74
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-293
NOTE:
AC310631 AD
Connector: C-16 <RHD>
AC310631AL
Connector: C-31 <RHD>
AC310619
Connectors: C-203, C-210 <RHD>
AP
Junction block side
Junction block (Front view)
C-210
C-203
Harness side
C-210
C-203
10
1
6
14
5
12
13
4
11
7
2
3
8
9
AC310220
AC310220
Connector: G-21 <RHD>
AG
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-294
<RH drive vehicles> Prior to the wiring harness
inspection, check intermediate connector C-16
<tail/stop lamp (LH) and licence plate lamp>, C-125
<tail/stop lamp and licence plate lamp>, G-14
<licence plate lamp>, G-21 <tail/stop lamp (LH)>,
joint connector C-31 <tail/stop lamp (RH)>, junction
block connector C-203 <tail/stop lamp (LH)> and
C-210 <tail/stop lamp (LH)>, and repair if necessary.
• Check the output lines for open circuit.
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Repair the wiring harness.
Step 8. Retest the system.
Check that the tail lamps, the position lamps and the
licence plate lamps illuminate normally.
Q: Is the check result normal?
The lamps illuminate normally at both high and low
beams. :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
When the tail/stop lamps do not illuminate :
Replace the tail/stop lamp socket assembly.
When the position lamps do not illuminate :
Replace the position lamp socket.
When the licence plate lamps do not illuminate :
Replace the licence plate lamp socket.
Inspection Procedure M-7: The headlamp(s) do not illuminate.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
FRONT-ECU
HEADLAMP
(HI: LH)
HEADLAMP
(LO: LH)
HEADLAMP
(LO: RH)
HEADLAMP
(HI: RH)
HEADLAMP
RELAY: HI
HEADLAMP
RELAY: LO
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
RELAY BOX
Headlamps Circuit
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-295
COMMENTS ON TROUBLE SYMPTOM
If any of the headlamps or the high-beam indicator
does not illuminate, the wiring harness connector(s),
the bulb or the fuse may be defective or burned out.
POSSIBLE CAUSES
• Malfunction of the headlamp bulbs
• Malfunction of the high-beam indicator bulb
• Damaged harness wires and connectors
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-296
DIAGNOSIS PROCEDURE
Step 1. Connector check: A-35 headlamp (HI: RH)
connector or A-21 headlamp (HI: LH) connector,
A-38 headlamp (LO: RH) connector or A-18
headlamp (LO: LH) connector
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст