Mitsubishi Grandis. Manual — part 366
COMBINATION METER
CHASSIS ELECTRICAL
54A-83
FUEL TANK GAUGE UNIT FLOAT HEIGHT
FUEL TANK PUMP AND GAUGE UNIT
ASSEMBLY
1. Move the float and check that F position height (A)
and E position height (B) are at the standard
values when the float arm touches the stopper.
Standard values:
2. If all checks are correct, go to fuel tank gauge unit
float height check. If any check is not correct,
replace the fuel tank gauge unit.
FUEL TANK GAUGE UNIT
1. Move the float and check that F position height (A)
and E position height (B) are at the standard
values when the float arm touches the stopper.
Standard values:
2. If all checks are correct, go to fuel tank gauge unit
float height check. If any check is not correct,
replace the fuel tank gauge unit.
Float Position
Float Centre Height
F position (A)
57.6
± 3 mm
E position (B)
158.4
± 3 mm
AC312743AB
F position
E position
Stopper
A
B
Float Position
Float Centre Height
F position (A)
57.0
± 3 mm
E position (B)
180.2
± 3 mm
AC312743AB
A
B
F position
E position
Stopper
COMBINATION METER
CHASSIS ELECTRICAL
54A-84
COMBINATION METER ASSEMBLY
REMOVAL AND INSTALLATION
M1543019800101
CAUTION
When the battery cable is disconnected or the combination meter is removed, the fuel gauge learned
value will be erased. To let the display unit re-learn it, enter the vehicle speed (by driving the vehicle
or entering simulated vehicle speed) and then stop the vehicle. Service on a level surface. (If the
vehicle is inclined, the measurement value will go out.)
DISASSEMBLY AND REASSEMBLY
M1543019900108
AC311964AB
1
2
Removal steps
•
Steering column cover (Refer to
GROUP 52A, Instrument Panel
Assembly
1.
Combination meter bezel (Refer
to GROUP 52A, Instrument Panel
Assembly
).
2.
Combination meter assembly
Removal steps (Continued)
AC313279
AB
1
2
HEADLAMP
CHASSIS ELECTRICAL
54A-85
HEADLAMP
SERVICE SPECIFICATIONS
M1542000300495
PRECAUTIONS ON HOW TO USE THE
HEADLAMP ASSEMBLY
Be careful with the following items as resin lenses
are used in the headlamp assembly.
• Don't illuminate the headlamp for three minutes
or more when the headlamp is covered with
scratch protector.
• Don't tape the outer lens.
• Don't scratch the outer lens surface with a sharp
edged special tool.
• Use the specified wax remover and rinse the wax
off cleanly.
• Use the specified genuine bulb.
TROUBLESHOOTING
M1542011800201
Features the headlamp automatic-shutdown function
to avoid battery drain when the headlamps are left
on. The main features are as follows:
• Extinguishes automatically in three minutes if the
ignition switch is turned off with the lighting switch
on.
• Extinguishes in one second if the driver's door is
opened within that 3-minute period.
• If the headlamps are turned on with the ignition
switch off, the headlamps and tail lamps will
extinguish in three minutes after the driver's door
is opened or closed.
The headlamps are controlled by the Smart Wiring
System (SWS). For troubleshooting, refer to
respective Groups below.
• Not using SWS monitor: GROUP 54B,
Troubleshooting
.
• Using SWS monitor: GROUP 54C,
Troubleshooting
.
ON-VEHICLE SERVICE
HEADLAMP AIMING
M1542000900635
<USING A BEAM SETTING EQUIPMENT>
1. The headlamps should be aimed with the proper
beam setting equipment, and in accordance with
the equipment manufacture’s instructions.
2. Alternately turn the adjusting screw to adjust the
headlamp aiming.
Disassembly steps
1.
Combination meter glass
2.
Combination meter
Item
Standard value
Limit
Headlamp aiming
Vertical direction 60 mm below horizontal
(H)
−
Horizontal
direction
15
° sloping section
intersects the vertical
line (V)
−
Headlamp luminous intensity measurement cd
(Corresponding to the illumination 40 m ahead of the
vehicle at low beam)
−
30,000 cd or more
AC102583
HEADLAMP
CHASSIS ELECTRICAL
54A-86
<USING A SCREEN>
1. Inflate the tyres to the specified pressures and
there should be no other load in the vehicles other
than driver or substituted weight of approximately
75 kg placed in driver’s position.
2. Put the headlamp levelling switch in "0" position.
3. Set the distance between the screen and the
centre marks of the headlamps as shown in the
illumination.
4. Check if the beam shining onto the screen is at
the standard value.
Standard value:
(Vertical direction) 60 mm below horizontal
(H)
(Horizontal direction) 15
° sloping section
intersects the vertical line (V)
NOTE: The illustration shows LH drive vehicles.
For RH drive vehicles, it is symmetrical.
CAUTION
Be sure to adjust the aiming adjustment screw in
the tightening direction.
5. Alternately turn the adjusting screw to adjust the
headlamp aiming.
HEADLAMP INTENSITY MEASUREMENT
M1542001000550
Using a photometer, and following its manufacture’s
instruction manual, measure the headlamp intensity
and check to be sure that the limit value is satisfied.
Limit: 30,000 cd or more
AC312769
Headlamp centre line
Vehicle centre line
Screen
5 m
Lamp centre
AB
AC312781
(H)
(V)
AB
Lamp centre
15
High intensity zone
Distance of
vertical direction
AC312820AB
Vertical direction
adjustment
Horizontal direction
adjustment
Vertical direction
adjustment
Horizontal direction
adjustment
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст