Mitsubishi Grandis. Manual — part 367
HEADLAMP
CHASSIS ELECTRICAL
54A-87
NOTE:
.
1. When measuring the intensity, maintain an
engine speed of 2,000 r/min, with the battery in
the charging condition.
2. There may be special local regulations pertaining
to headlamp intensity, be sure to make any
adjustments necessary to satisfy such
regulations.
3. If an illuminometer is used to make the
measurements, convert its values to photometer
values by using the following formula.
I = Er
2
Where:
I=intensity (cd)
E=illumination (Iux)
r=distance (m) from headlamps to
illuminometer
BULB REPLACEMENT
M1542001300818
HEADLAMP BULB <LOW BEAM>
REPLACEMENT
1. Disconnect the connector.
2. Twist the cover to remove.
3. Withdraw the socket from the bulb.
CAUTION
Don't touch the bulb surface with bare hands or
dirty gloves. if the bulb surface (glass part) gets
dirty, clean it with alcohol or thinner immediately
and dry well, and then install it.
4. Remove the spring to withdraw the bulb.
HEADLAMP BULB <HIGH BEAM>
REPLACEMENT
1. Disconnect the connector.
2. Twist the cover to remove.
CAUTION
Don't touch the bulb surface with bare hands or
dirty gloves. if the bulb surface (glass part) gets
dirty, clean it with alcohol or thinner immediately
and dry well, and then install it.
3. Twist the socket to remove.
POSITION LAMP BULB REPLACEMENT
CAUTION
Don't touch the bulb surface with bare hands or
dirty gloves. if the bulb surface (glass part) gets
dirty, clean it with alcohol or thinner immediately
and dry well, and then install it.
Disconnect the connector, and twist the position
lamp socket to remove it.
AC301627
AD
Cover
AC301626
AC
Cover
AC301625
AC
Position lamp
HEADLAMP
CHASSIS ELECTRICAL
54A-88
FRONT TURN SIGNAL LAMP BULB
REPLACEMENT
CAUTION
Don't touch the bulb surface with bare hands or
dirty gloves. if the bulb surface (glass part) gets
dirty, clean it with alcohol or thinner immediately
and dry well, and then install it.
Disconnect the connector, and twist the front turn
signal lamp socket to remove it.
HEADLAMP AUTOMATIC-SHUTDOWN
FUNCTION CHECK
M1542011201194
Confirm that the headlamp turns off when the ignition
switch is ON and the driver's door is opened and
when the ignition key is pulled out with the lighting
switch at ON (HEAD) position and the driver's door is
opened. If not, carry out the troubleshooting. (Refer
to GROUP 54B, Troubleshooting
GROUP 54C, Troubleshooting
AC301624
AC
Front turn-signal lamp
HEADLAMP
CHASSIS ELECTRICAL
54A-89
HEADLAMP
REMOVAL AND INSTALLATION
M1542001800318
AC312842 AB
1
2
3
4
2.5 ± 0.3 N·m
4.9 ± 0.7 N·m
4.9 ± 0.7 N·m
4.9 ± 0.7 N·m
Headlamp levelling switch
removal steps
•
Lower panel (Refer to GROUP 52A,
Instrument Panel Assembly
1.
Headlamp levelling switch
Headlamp removal steps
2.
Air guide panel
<<A>>
3.
Headlamp assembly
4.
Headlamp bracket
FRONT FOG LAMP
CHASSIS ELECTRICAL
54A-90
REMOVAL SERVICE POINTS
<<A>> HEADLAMP ASSEMBLY
REMOVAL
1. Remove the splash shield assembling clips as
shown.
2. Remove the front bumper assembling bolts and
clips as shown.
3. Remove the headlamp assembly by sliding out
the front bumper.
INSPECTION
M1542011201224
HEADLAMP LEVELLING SWITCH CHECK
FRONT FOG LAMP
SERVICE SPECIFICATIONS
M1542000300525
AC303130
AC312846
Switch position
Resistance value
between 4 TAG 5
0
120
Ω
1
300
Ω
2
620
Ω
3
1.1 k
Ω
4
2 k
Ω
AC302750AB
Item
Standard value
Fog lamp aiming
Vertical direction
100 mm below horizontal (H)
Horizontal direction
Parallel to direction of vehicle
travel
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст