Mitsubishi Grandis. Manual — part 94
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-373
COMMENTS ON TROUBLE SYMPTOM
If the room lamp does not illuminate or extinguish
normally, wiring harness connector(s) or the bulb
may be defective.
POSSIBLE CAUSES
• Malfunction of the interior lamp switches
• Malfunction of the room lamp bulbs
• Malfunction of the rear personal lamp bulbs
• Damaged harness wires and connectors
ETACS-ECU
J/B SIDE
ROOM LAMP
INTERIOR
LAMP
SWITCH
REAR
PERSONAL
LAMP
FOR
SECOND
SEAT: LH
REAR
PERSONAL
LAMP
FOR
SECOND
SEAT: RH
REAR
PERSONAL
LAMP
FOR
THIRD
SEAT: LH
REAR PERSONAL LAMP
(FOR THIRD SEAT: RH)
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Room Lamp and Rear Personal Lamp Circuit
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-374
DIAGNOSTIC PROCEDURE
Step 1. Pulse check
Check the input signals below, which are related to
the room lamp.
OK: The MUT-III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
All the signals are received normally. :
Go to Step
All the door switch signals are not received. :
Refer to inspection procedure Q-14 "All the
door switch signals are not received <LH
drive vehicles>
vehicles>
The driver's door lock actuator switch signal is not
received. :
Refer to inspection procedure Q-15
"The driver's door lock actuator switch
signal is not received <LH drive
vehicles>
or <RH drive
vehicles>
The interior lamp switch signal is not received. :
Refer to inspection procedure Q-22 "The
interior lamp "all on" or "all off" switch signal
is not sent to the ETACS-ECU
."
Step 2. Retest the system.
Check that the right or left room lamp illuminates
when the interior lamp switch is operated.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 3.
Step 3. Connector check: C-219 ETACS-ECU
connector, E-02 room lamp connector
Q: Is the check result normal?
System switch
Check condition
Driver's door switch
Driver's door is opened
while all the other doors
are closed.
Passenger’s door switch Passenger's door is
opened while all the
other doors are closed.
Rear door (RH) switch
Rear door (RH) is
opened while all the
other doors are closed
Rear door (LH) switch
Rear door (LH) door is
opened while all the
other doors are closed
Tailgate switch
TAilgate is opened while
all the other doors are
closed
Driver's door lock
actuator switch
When the driver's door is
unlocked or locked
Interior lamp ON switch
When turned from OFF
to ON
Interior lamp OFF switch When turned from ON to
OFF
AC310626
Connector: C-219
Junction block (Rear view)
<LHD>
AB
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC310651
AD
Connector: E-02 <LHD>
Harness side
AC310655
AE
Connector: E-02 <RHD>
Harness side
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-375
YES :
Go to Step 4.
NO :
Repair the defective connector.
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-376
Step 4. Check the wiring harness from C-219
ETACS-ECU connector terminal No.6 to E-02
room lamp connector terminal No.10.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст