Mitsubishi Grandis. Manual — part 683
SUNROOF ASSEMBLY
BODY
42-60
REASSEMBLY SERVICE POINT
>>A<< BATTERY INSTALLATION
CAUTION
Do not allow water or dust to enter the inside of
the transmitter assembly when it is open. Also,
do not touch the precision electronic device.
Install a new battery to the transmitter assembly with
its (+) side facing towards the case side.
Battery required for replacement: Coin type
battery CR1616
INSPECTION
M1428003800078
TRANSMITTER BATTERY CHECK
Measure the voltage of the battery. If the voltage of
the battery is not within the standard value, replace
the battery.
Standard value:2.5
− 3.2 V
SUNROOF ASSEMBLY
SERVICE SPECIFICATIONS
M1421000300329
TROUBLESHOOTING
M1426000700366
The rear sunroof system is controlled by the Smart
Wiring System (SWS). For troubleshooting, refer to
GROUP 54B, Troubleshooting
, or GROUP
54C, Troubleshooting
.
ON-VEHICLE SERVICE
WATER TEST
M1426000900296
Check if there are any leaks in the sunroof by the
following procedure.
1. Fully close the roof lid glass.
2. Adjust the water pressure so that water comes out
of the hose to a height of approximately 50 cm
when the hose is held vertically facing upwards.
3. Hold the end of the hose approximately 30 cm
above the roof and let the water run onto the
weatherstrip for 5 minutes or more.
4. Check if any water leaks can be found in the room
while watering. Even though there are any water
leaks around the roof lid glass, it can be
acceptable as long as water is caught in the drip
area.
REAR SUNROOF FIT ADJUSTMENT
M1426001000315
1. Close the rear roof lid glass fully.
2. Open the rear sun shade fully.
AC304118
+
Master key side
Case side
Battery
Transmitter assembly
–
AC
AC004486
Item
Standard value
Roof lid glass operation current A (at 20
°C)
7 or less
AC310857AB
Hose
Approx
30 cm
SUNROOF ASSEMBLY
BODY
42-61
3. Loosen the rear roof lid glass assembly mounting
screws. Adjust the rear roof lid glass height by
moving the glass assembly along the guide
oblong hole so that the clearance between the
glass and the vehicle body is even.
4. After adjustment, check that the rear sunroof
operates smoothly.
SUNROOF CHECK
M1426004700131
Check to see that the rear sunroof operates by
pressing the sunroof switch. Perform troubleshooting
if operations malfunction. Refer to GROUP 54B,
Troubleshooting
Troubleshooting
.
SUNROOF LOCK SWITCH FUNCTION
INSPECTION
M1426005600018
When the window lock switch (sunroof lock switch) of
the driver's power window switch is turned on, the
sunroof switch should be disabled. If the sunroof
operates, perform troubleshooting. Refer to GROUP
54B, Troubleshooting
or GROUP 54C,
Troubleshooting
.
REAR SUNROOF SAFETY FUNCTION
CHECK
M1426004400163
1. Close the rear roof lid glass by applying an
approximately 10mm thickness wood chip placed
at a right angle to the rear roof lid glass.
2. Check to see if the rear roof lid glass opens after
the sunroof motor assembly turns when the rear
roof lid glass catches the wooden chip. Refer to
GROUP 54B, Troubleshooting
GROUP 54C, Troubleshooting
REAR ROOF LID GLASS OPERATION
CURRENT CHECK
M1426003200188
1. Remove the sunroof fuse from the fuse box, and
then connect a circuit tester as shown.
2. Operate the sunroof switch to open the sunroof.
Measure when the sunroof is half opened.
Standard value: 7 A or less (at 20
°C)
3. Check the following areas if the operating current
of the rear roof lid glass exceeds the standard
value.
• Improperly installed rear sunroof assembly,
deformation or any foreign substances
• Drive cable fastening
• Tilting of rear roof lid glass
INITIALISATION OF REAR SUNROOF
M1426004600145
If the sunroof motor assembly is removed or the
anti-trap function is triggered at least consecutively
five times, perform the initialisation below.
1. Press and hold the OPEN switch to move the roof
lid glass from the fully closed position to the fully
opened position.
2. Press and hold the CLOSE switch to move the
roof lid glass from the fully opened position to the
fully closed position.
NOTE: If the rood lid glass stops halfway when
the switch is pressed and held, the initialisation
process has not been completed properly. Repeat
the initialisation process above.
AC303358AB
AC309960
AC310862 AB
<LH drive vehicles>
AC309956
AC310864AB
<RH drive vehicles>
SUNROOF ASSEMBLY
BODY
42-62
SUNROOF ASSEMBLY
REMOVAL AND INSTALLATION
M1426001200405
Post-installation Operation <Front roof lid glass
assembly, Front tilt up sunroof assembly>
• Sunroof Water Test (Refer to
AC310746 AB
1
12
7
8
14
5
14
5
13
13
2
10
9
6
6
11
4
3
<Front sunroof assembly>
Front sunroof lid glass assembly
removal steps
•
Headlining assembly (Refer to
GROUP 52A, Headlining
1.
Sunroof lid latch
2.
Front sunroof lid glass assembly
3.
Sunroof lid outer weatherstrip
Opening weatherstrip removal
4.
Opening weatherstrip
Front sunroof assembly removal
steps
•
Headlining assembly (Refer to
GROUP 52A, Headlining
5.
Sunroof drain pipe connection
6.
Centre drain pipe connection
7.
Front sunroof assembly
Striker removal steps
•
Headlining assembly (Refer to
GROUP 52A, Headlining
8.
Striker
SUNROOF ASSEMBLY
BODY
42-63
Sunshade removal steps
•
Headlining assembly (Refer to
GROUP 52A, Headlining
5.
Sunroof drain pipe
6.
Centre drain pipe connection
7.
Front sunroof assembly
9.
Front sunroof sunshade rear
10. Front tilt up sunroof sunshade front
11. Front tilt up sunroof sunshade
stopper
Tilt roof rail removal steps
•
Headlining assembly (Refer to
GROUP 52A, Headlining
2.
Front sunroof lid glass assembly
7.
Front sunroof assembly
12. Tilt roof rail
Front drain pipe removal steps
•
Instrument panel assembly (Refer
to GROUP 52A, Instrument Panel
Assembly
•
Headlining assembly (Refer to
GROUP 52A, Headlining
5.
Sunroof drain pipe
•
Splash shield (Refer to
).
>>A<<
13. Front drain pipe
14. Grommet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст