Mitsubishi Grandis. Manual — part 353
COMBINATION METER
CHASSIS ELECTRICAL
54A-31
REMOVAL SERVICE POINT
<<A>> STEERING LOCK CYLINDER
REMOVAL
1. Insert the key in the steering lock cylinder and turn
it to the "ACC" position.
2. Using a small Phillips head screwdriver, pull the
steering lock cylinder toward you.
INSPECTION
M1543019502827
IGNITION SWITCH CONTINUITY CHECK
Disconnect ignition switch connector C-307 without
removing the ignition switch. Then check the
continuity.
KEY REMINDER SWITCH CONTINUITY
CHECK
Disconnect key reminder switch connector C-308
without removing the ignition switch and key
reminder switch. Then check the continuity.
COMBINATION METER
SERVICE SPECIFICATIONS
M1543000300465
AC302621AB
Lock pin
AC302623
3
6
1
4
2
5
AB
Switch position Tester
connection
Specified
condition
"LOCK" (OFF)
1
− 2, 1 − 4, 1 − 5,
1
− 6
Open
circuit
"ACC"
1
− 6
Less than 2
ohms
"ON"
1
− 2, 1 − 4, 1 − 6,
2
− 4, 2 − 6, 4 − 6
Less than 2
ohms
"START"
1
− 2, 1 − 5, 2 − 5
Less than 2
ohms
Status of ignition
key
Tester
connection
Specified
condition
Removed
4
− 6
Less than 2
ohms
Inserted
4
− 6
Open circuit
AC302622
6
2
7
5
1
3 4
AB
Item
Standard value
Limit
Speedometer indicating range km/h (mph)
20 (10)
20
− 24 (10 − 12)
−
40 (25)
40
− 44 (25 − 27)
−
80 (50)
80
− 85 (50 − 53)
−
120 (75)
121
− 127 (76 − 80)
−
160 (100)
162
− 169 (101 − 106) −
200 (125)
203
− 211 (127 − 132) −
The voltmeter needle fluctuation km/h (Vehicle speed is 35km/h or more) −
± 3
COMBINATION METER
CHASSIS ELECTRICAL
54A-32
Tachometer indicating error r/min
2,000
± 100
−
6,000
± 200
−
Fuel tank pump and gauge unit assembly
resistance
Ω
Float position F
(highest)
6.5
± 1
−
Float position E
(lowest)
53.2
± 1
−
Fuel tank gauge unit assembly resistance
Ω
Float position F
(highest)
6.5
± 1
−
Float position E
(lowest)
66.8
± 1
−
Fuel tank pump and gauge unit assembly float
height mm
Float position F (A)
57.6
± 3
−
Float position E (B)
158.4
± 3
−
Fuel tank gauge unit float height mm
Float position F (A)
57.0
± 3
−
Float position E (B)
180.2
± 3
−
Item
Standard value
Limit
COMBINATION METER
CHASSIS ELECTRICAL
54A-33
SPECIAL TOOLS
M1543000602042
COMBINATION METER
CHASSIS ELECTRICAL
54A-34
Tool
Number
Name
Application
MB990784
Ornament
remover
Removal of meter bezel
MB991955
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991825
F: MB991826
MUT-III
sub-assembly
A: (V. C.I.)
Vehicle
communicatio
n interface
B: MUT-III USB
cable
C: MUT-III Main
harness A
(Vehicles with
CAN
communicatio
n system)
D: MUT-III Main
harness B
(Vehicles
without CAN
communicatio
n system)
E: MUT-III
Measurement
adapter
F: MUT-III
Trigger
harness
Combination meter (incorporating
the meter-ECU) check (Diagnosis
code, service data, actuator test)
CAUTION
For vehicles with CAN
communication, use MUT-III main
harness A to send simulated
vehicle speed. If you connect
MUT-III main harness B instead,
the CAN communication does
not function correctly.
MB990784
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
A
B
C
D
E
F
DO NOT USED
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст