Mitsubishi Grandis. Manual — part 352
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-27
1. Connect the MUT-III to the diagnosis connector
(16-pin).
2. Turn the ignition switch to "ON" position.
3. Select "System select" from the start-up screen.
4. Choose "IMMOBILIZER" from the "POWER
TRAIN" tab.
5. Choose "Special Function" from "IMMOBILIZER"
screen.
6. Choose "Key registration" from "Special Function"
screen.
7. Enter the vehicle’s password (secret code) on the
"Key registration" screen, and then click the check
mark icon. Follow the prompts on the screen to
insert key(s) into the ignition switch to begin key
registration.
AC302297
AC310120
AB
MB991827
16-pin
MB991910
MB991824
System select
Special function
CAN bus diagnosis
Function Select Menu
Menu
AC209666
Maintenance
AD
MPI/GDI/DIESEL
ELC-A/T/CVT
IMMOBILIZER
SS4II
TCL/STARLTY CONTROL
AUTO CRUISE
CHASSIS
BODY
System Select Menu
POWER TRAIN
AC305175
Check Chart For
Problem Sy
Data List
Special
Function
Self-diagnosis
Simulated Vehicle
Speed Out
Resistor
Voltmeter
POWERTRAIN
IMMOBILIZER
IMMOBILIZER
AC305176
Key ID registration
Additional Key
Registration
POWERTRAIN
Special Function
IMMOBILIZER
Special Function
AC305177
POWERTRAIN
IMMOBILIZER
Special Function
7
8
9
4
5
6
1
2
3
0
Back
Back
Space
Space
Clear
Clear
Key registration
AC207300
AD
POWERTRAIN
IMMOBILIZER
Special Function
IMMOBILIZER-ECU registration
Progress
In-Complete
Key registration
AC207302
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-28
8. If the key ID was registered successfully,
"Progress" indication will turn active (gray). Then
the registration process completes. If the key ID
failed to be registered, "In-Complete" indication
will turn active (gray).
9. The number of keys currently registered will be
displayed. To register an additional key, replace
the ignition key with the next key to be registered
within five seconds. Key ID registration screen will
be displayed, then register another key.
NOTE: A maximum of eight different keys can be
registered.
10.This completes the registration operation. Turn
the ignition switch "LOCK" (OFF) and leave it off
for approximately ten seconds.
11.Check that the engine can be started with each of
the ignition keys.
12.Check that the immobilizer system diagnosis
code and MPI system diagnosis code did not set.
13.If not diagnosis code is shown, terminate the
MUT-III.
14.Turn the ignition switch to "LOCK" (OFF) position.
15.Disconnect MUT-III.
REGISTRATION OF ADDITIONAL KEYS
WITH THE MUT-III
Additional key(s) can be registered with the MUT-III
while keeping all existing key data.
CAUTION
To prevent damage to MUT-III, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting MUT-III.
NOTE: To register additional keys with the MUT-III,
no registered keys must be lost.
1. Connect MUT-III to the 16-pin diagnosis
connector.
2. Turn the ignition switch to "ON" position.
NOTE: Before registration, check that no diagnosis
code is set. If a diagnosis code is set, resolve the
problem beforehand.
3. Carry out steps 3 to 6 of the sub-section
"Registration with MUT-III."
4. Choose "Transponder ID addition" from "Special
Function" screen.
AC302297
AC310120
AB
MB991827
16-pin
MB991910
MB991824
Key ID registration
Additional Key
Registration
POWERTRAIN
Special Function
IMMOBILIZER
Special Function
AC305177
POWERTRAIN
IMMOBILIZER
Password
Special Function
7
8
9
4
5
6
1
2
3
0
Back
Back
Space
Space
Clear
Clear
Trasponder ID addition
AC207301
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-29
5. Enter the vehicles password (secret code) on the
"Transponder ID addition" screen, and then click
the check mark icon.
6. If an additional registration is made successfully,
the screen will ask if another key is registered or
not. If the third ignition key is registered, remove
the key, which has been registered. Then insert
the third key within five seconds, and then turn it
to the ON position.
7. Register the additional ignition key according to
step 6 above. The number of the registered
ignition keys are shown on "The number of
registered key" screen.
NOTE: A maximum of eight different keys can be
registered.
8. This completes the registration operation. Turn
the ignition switch "LOCK" (OFF) and leave it off
for approximately ten seconds.
9. Check that the engine can be started with each of
the ignition keys.
10.Check that the immobilizer system diagnosis
code and MPI system diagnosis code did not set.
11.If not diagnosis code is shown, terminate the
MUT-III.
12.Turn the ignition switch to "LOCK" (OFF) position.
13.Disconnect MUT-III.
AC207301
AC209775
POWERTRAIN
IMMOBILIZER
Key ID register
The number of registered key
The number of registered key
3
Progre
Special Function
Trasponder ID addition
About Additional Transponder
ID SET
If register another key ID, press the
If register another key ID, press the
OK button after inserting a new key
OK button after inserting a new key
within 5 sec and turning on IG-SW
within 5 sec and turning on IG-SW.
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-30
IGNITION SWITCH
REMOVAL AND INSTALLATION
M1543002100575
WARNING
•
Before removal of the air bag module, refer to GROUP 52B, Service Precautions (
and Driver’s, Front Passenger’s Air Bag Module(s) and Clock Spring (
•
When removing and installing the steering wheel, do not let it bump against the air bag
module.
AC311940
1
1
2
3
4
5
6
7
AB
2.5 ± 0.5 N·m
Removal steps
•
Gearshift lever knob <M/T> (Refer
to GROUP 22A, Transmission
Control
•
Selector lever knob <A/T> (Refer to
GROUP 23A, Transmission Control
•
Selector lever panel (Refer to
GROUP 52A, Instrument Panel
Assembly
•
Front scuff plate inner, Cowl side
trim (Refer to GROUP 52A, Interior
Trim
).
•
Fuel filler lid lock release handle
(Refer to GROUP 42, Fuel Filler Lid
•
Lower panel (Refer to GROUP 52A,
Instrument Panel Assembly
1.
Steering column cover (Refer to
GROUP 52A, Instrument Panel
Assembly
).
2.
Steering wheel (Refer to GROUP
37A, Steering Wheel
3.
Clock spring and column switch
assembly (Refer to GROUP 37A,
Steering Shaft
and
GROUP 52B, Driver’s, Front
Passenger’s Air Bag Module(s) and
Clock Spring
).
4.
Ignition Switch
5.
Key reminder switch
6.
Immobilizer-ECU and key ring
antenna assembly
<<A>>
7.
Steering lock cylinder
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст