Mitsubishi Grandis. Manual — part 166
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-126
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 14. Connector check: F-08 door lock
actuator (rear: LH) connector
Q: Is the check result normal?
YES :
Go to Step 15.
NO :
Repair the defective connector.
Step 15. Check the door lock actuator (rear: LH).
Check that the door lock actuator (rear: LH) is in
good condition. Refer to GROUP 42
− Door
Q: Is the check result normal?
YES :
Go to Step 16.
NO :
Replace the door lock actuator (rear: LH).
Step 16. Connector check: C-219 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 17.
NO :
Repair the defective connector.
Step 17. Check the wiring harness from C-219
ETACS-ECU connector terminal Nos.12 and 13 to
F-08 door lock actuator (rear: LH) connector
terminal Nos.4 and 6.
NOTE:
Prior to the wiring harness inspection, check D-16
intermediate connectors and C-210 junction block
connector, and repair if necessary.
• Check the input and output lines for open circuit.
Q: Is the check result normal?
AC310209
Connector: F-08
Harness side
AD
F-08(B)
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC310209
Connector: F-08
Harness side
AD
F-08(B)
AC310618
Connector: C-210 <RHD>
AO
Junction block (Front view)
Harness side
AC310207
AB
Connector: D-16
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-127
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Inspection Procedure C-6: The tailgate cannot be opened or closed.
COMMENT ON TROUBLE SYMPTOM
If a door or the tailgate can not be locked or unlocked
by the central door locking system, the tailgate lock
actuator or the ETACS-ECU may be defective.
POSSIBLE CAUSES
• Malfunction of the tailgate lock actuator
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
Step 1. Check that the central door locking
system and the keyless entry system operate.
Check that the doors (excluding the tailgate) are
locked and unlocked normally when the central door
locking and keyless entry systems are operated.
Q: Is the check result normal?
ETACS-ECU
TAILGATE
LOCK ACTUATOR
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Tailgate Open Circuit
TAILGATE
OPEN RELAY
J/B SIDE
INPUT SIGNAL
TAIL GATE LOCK
RELEASE HANDLE
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-128
YES <The central door locking and keyless entry
systems operate normally> :
Go to Step 2
NO <The central door locking system does not
operate normally> :
Refer to Inspection Procedure
C-1 "Central door locking system does not
work
NO <The keyless entry system does not operate
normally> :
Refer to Inspection Procedure E-1
"Keyless entry system does not work
Step 2. SWS monitor data list
Check the SWS communication input signal, which
are related to the tailgate opening and closing.
<Selected item> ETACS ECU
• Ignition switch: from OFF to ON
OK: Normal condition is displayed.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Refer to Inspection Procedure Q-2 "The
ignition switch (IG1) signal is not received
Step 3. ETACS switch data by using the SWS
monitor
Check the ETACS-ECU signal related to the tailgate
opening and closing.
• Tailgate lock release handle: from OFF to ON
OK: Normal condition is displayed.
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Replace the ETACS-ECU.
Step 4. Connector check: G-17 tailgate lock
actuator connector
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the defective connector.
Step 5. Check the tailgate lock actuator.
Check that the tailgate lock actuator is in good
condition. Refer to GROUP 42
− Tailgate
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Replace the tailgate lock actuator.
Step 6. Resistance measurement at the G-17
tailgate lock actuator connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Resistance between G-17 tailgate lock actuator
Item No.
Item name
Normal condition
Item 30
IG SW(IG1)
from OFF to ON
Item No.
Item name
Normal conditions
Item 30
GTE OPENER
SW
OFF to ON (only when
switch is operated)
AC310222
Connector: G-17
Harness side
AD
G-17(B)
AC310222
Connector: G-17
Harness side
AD
G-17(B)
AC209364
AC209364MR
CONNECTOR G-17
(HARNESS SIDE)
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-129
connector terminal No.2 and body earth
OK: 2
Ω or less
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Go to Step 7.
Step 7. Check the wiring harness between G-17
tailgate lock actuator connector terminal No.2
and the body earth.
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 8. Connector check: C-221 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 9.
NO :
Repair the defective connector.
AC310222
Connector: G-17
Harness side
AD
G-17(B)
AC310626
Connector: C-221
Junction block (Rear view)
<LHD>
AC
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
Harness side
C-221(GR)
AC310620
Connector: C-221
Junction block
(Rear view)
<RHD>
AC
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
Harness side
C-221(GR)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст