Mitsubishi Grandis. Manual — part 888
COIL SPRING
REAR SUSPENSION
34-6
REMOVAL SERVICE POINT
<<A>> REAR SHOCK ABSORBER BOLT
REMOVAL
After supporting the semi-trailing arm rear shock
absorber mounting area with a jack, remove the rear
shock absorber bolt.
INSTALLATION SERVICE POINTS
>>A<< REAR SUSPENSION SPRING
LOWER PAD/REAR SUSPENSION COIL
SPRING INSTALLATION
Fit the lower pad into the coil spring end, and then
align the bottom of coil spring with the spring seat
groove of semi - trailing arm.
AC302431AC
Semi-trailing
arm
Shock
absorber
AC302049 AC
Semi-trailing arm
Lower pad
Coil spring
SEMI-TRAILING ARM ASSEMBLY (LOWER ARM ASSEMBLY)
REAR SUSPENSION
34-7
SEMI-TRAILING ARM ASSEMBLY (LOWER ARM
ASSEMBLY)
REMOVAL AND INSTALLATION
M1341017500029
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in the unladen condition.
Pre-removal Operation
• Rear Brake Caliper Assembly and Brake Disc Removal
(Refer to GROUP 35A, Rear Disc Brake Assembly
• Rear Hub Assembly Removal (Refer to GROUP 27, Rear
• Parking Brake Shoe and Lining Assembly Removal (Refer
to GROUP 36, Parking Brake Lining and Drum
).
• Parking Brake Rear Cable Clamp and Backing Plate side
disconnection (Refer to GROUP 36, Parking Brake Cable
,
• Rear Wheel Speed Sensor Removal (Refer to GROUP
35B, Wheel Speed Sensor
).
• Backing Plate Removal (Refer to GROUP 36, Parking
Brake Lining and Drum
• Rear Suspension Coil Spring Removal (Refer to
).
• Rear Brake Hose Clamp disconnection
Post-installation Operation
• Rear Brake Hose Clamp connection
• Rear Suspension Coil Spring Installation (Refer to
).
• Backing Plate Installation (Refer to GROUP 36, Parking
• Rear Wheel Speed Sensor Installation (Refer to GROUP
35B, Wheel Speed Sensor
• Parking Brake Rear Cable Clamp and Backing Plate side
connection (Refer to GROUP 36, Parking Brake Cable
,
• Parking Brake Shoe and Lining Assembly Removal (Refer
to GROUP 36, Parking Brake Lining and Drum
• Rear Hub Assembly Installation (Refer to GROUP 27,
• Rear Brake Caliper Assembly and Brake Disc Installation
(Refer to GROUP 35A, Rear Disc Brake Assembly
• Rear Wheel Alignment Check and Adjustment (Refer to
).
• Parking Brake Lever Stroke Adjustment (Refer to
GROUP 36, On-vehicle Service
− Parking Brake Lever
Stroke Check and Adjustment
AC302051AC
1
2
3
4
5
N
60 ± 5 N·m
95 ± 10 N·m
Removal steps
<<A>>
>>B<<
1.
Rear suspension independent arm
bolt
2.
Rear suspension lower arm plate
3.
Rear suspension independent arm
bolt
>>A<<
4.
Rear suspension trailing arm
bushing stopper
5.
Semi-trailing arm assembly (rear
suspension lower arm)
Removal steps (Continued)
SEMI-TRAILING ARM ASSEMBLY (LOWER ARM ASSEMBLY)
REAR SUSPENSION
34-8
REMOVAL SERVICE POINT
<<A>> REAR SUSPENSION
INDEPENDENT ARM BOLT REMOVAL
After making the alignment marks on bolt and rear
suspension crossmember, remove the bolt.
INSTALLATION SERVICE POINTS
>>A<< REAR SUSPENSION TRAILING
ARM BUSHING STOPPER INSTALLATION
1. After aligning the stopper notch and semi-trailing
arm (lower arm) boss, insert the stopper into the
semi-trailing arm (lower arm).
2. Rotate the stopper by 90 degrees and fix it.
>>B<< REAR SUSPENSION
INDEPENDENT ARM BOLT
INSTALLATION
Align the mating marks and install the bolt.
INSPECTION
M1341017600026
• Check the bushings for wear and deterioration.
• Check the semi-trailing arm for bending or
damage.
AC302046AE
Semi-trailing arm
AC302052AC
A
A
Section A - A
Stopper
Semi-trailing
arm (lower
arm)
STABILIZER BAR
REAR SUSPENSION
34-9
STABILIZER BAR
REMOVAL AND INSTALLATION
M1341003000333
INSTALLATION SERVICE POINT
>>A<< REAR SUSPENSION STABILIZER
BAR BUSHING/REAR SUSPENSION
STABILIZER BAR BRACKET
INSTALLATION
Install the bushing and the bracket so that the
stabilizer bar identification mark is located in the
position shown in the illustration.
AC312503AB
8
7
9
1
3
4
5
N
6
25 ± 5 N·m
2
3
4
3
4
Removal steps
>>B<<
1.
Self-locking nut
2.
Bolt
3.
Joint cup (A)
4.
Stabilizer rubber
5.
Joint cup (B)
6.
Collar
>>A<<
7.
Rear suspension stabilizer bar
bracket
>>A<<
8.
Rear suspension stabilizer bar
bushing
9.
Rear suspension stabilizer bar
AC302432 AC
Bracket
Bushing
Stabilizer bar
Identification
mark
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст