Mitsubishi Grandis. Manual — part 869
TRANSMISSION CONTROL
AUTOMATIC TRANSMISSION (FF)
23A-143
REMOVAL SERVICE POINTS
<<A>> SELECTOR LEVER KNOB
REMOVAL
Pull out the selector knob to the direction shown.
INSTALLATION SERVICE POINTS
>>A<< TRANSMISSION CONTROL
CABLE ASSEMBLY (TRANSMISSION
SIDE) INSTALLATION
1. Place the selector lever and manual control lever
in the N position.
2. Tighten the transmission control cable locking nut
to the specified torque.
Tightening torque: 12
± 2 N⋅m
>>B<< KEY INTERLOCK CABLE
INSTALLATION
1. Selector lever to P position.
2. Turn the ignition key to LOCK (OFF) position.
3. Install the tip of the key interlock cable to the lock
cam of the selector lever assembly taking care not
to twist the inner cable.
4. Lift the lock guide (unlocked position) and then
install the adjuster case.
5. Lower the lock guide thoroughly and lock it.
NOTE: The lock position of the key interlock cable
is automatically adjusted by a spring.
AC311826AC
Selector lever knob
AC303714AE
Manual control lever
Locking nut
Transmission
control cable
Battery bracket
AC311846AB
A
Lock guide
Adjuster case
Spring
Lock
Unlock
Lock cam
Lock guide
Adjuster case
Key interlock
cable
Inner cable
View A
TRANSMISSION CONTROL
AUTOMATIC TRANSMISSION (FF)
23A-144
DISASSEMBLY AND REASSEMBLY
M1231006800471
REMOVAL SERVICE POINTS
<<A>> SELECTOR LEVER SUB
ASSEMBLY REMOVAL
A commercial plate type ratchet screwdriver is
recommended for removing the shift switch
assembly side tapping screws (two screws).
AC311926AB
Urethan adhesive: PANDO 156A
1
2
3
6
5
4
7
8
9
10
1
11
Disassembly steps
1.
Selector lever knob
2.
Garnish
3.
Pin
4.
Shift switch assembly
5.
Slider unit
6.
Slider
7.
Gate upper
8.
Lock cam
9.
Shift lock spring
10. Selector lever sub assembly
11. Lever mount bracket sub
assembly
AC311923AB
A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS
AUTOMATIC TRANSMISSION (FF)
23A-145
INSPECTION
M1231006900241
A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS
REMOVAL AND INSTALLATION
M1232001200563
CAUTION
When removing and installing the shift lock and key interlock cable, be careful not to hit the
SRS-ECU.
1
3 4 5 6
2
AC103390AC
Shift switch (up)
Select switch
Shift switch
(down)
Shift switch
assembly
OFF
ON
OFF
ON
OFF
ON
Switch position
Terminal NO.
Select switch
ON
1
− 4
OFF
1
− 2
Shift switch (up)
ON
3
− 6
OFF
−
Shift switch (down)
ON
3
− 5
OFF
−
Pre-removal Operation
• Selector Lever Assembly Removal (Refer to
Post-installation Operation
• Selector Lever Assembly Installation (Refer to
.)
• Key Interlock and Shift Lock Mechanism Check (Refer to
.)
• Selector lever operation check (Refer to
AC311663AB
1
2
3
4
A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS
AUTOMATIC TRANSMISSION (FF)
23A-146
REMOVAL SERVICE POINTS
<<A>> KEY INTERLOCK CABLE (ENGINE
STARTING SWITCH ASSEMBLY SIDE)
REMOVAL
Turn the ignition switch to the ACC position and then
pull the key interlock cable out from the ignition key
cylinder.
INSTALLATION SERVICE POINTS
>>A<< KEY INTERLOCK CABLE (ENGINE
STARTING SWITCH ASSEMBLY SIDE)
INSTALLATION
Turn the ignition switch to the ACC position and then
install the key interlock cable to the ignition key
cylinder.
Removal steps for key interlock
cable
•
Lower panel (Refer to GROUP
52A
− Instrument Panel
•
Steering column cover lower
(Refer to GROUP 37A
− Steering
Shaft
).
<<A>>
>>A<<
1.
Key interlock cable connection
(engine starting assembly side).
2.
Key interlock cable
Removal steps for shift lock
cable
3.
Shift lock cable connection (brake
pedal side)
4.
Shift lock cable
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст