Mitsubishi Grandis. Manual — part 825

MARK

EXTERIOR

51-35

INSPECTION

M1511019100697

HEADLAMP WASHER MOTOR CHECK

1. Remove the headlamp washer motor connector.
2. Check to see that the water is vigorously sprayed

when connecting the positive battery terminal to
terminal number 1 and terminal number 2 to the
negative battery terminal.

MARK

REMOVAL AND INSTALLATION

M1511011800409

INSTALLATION SERVICE POINT
>>A<< MARK APPLICATION

1. Installation position

Attach each mark to the position shown in the
illustration.

AC311181

1 2

AC310966

1

2

3

AB

Removal

1. Front three-diamond mark

>>A<<

2. Rear three-diamond mark

>>A<<

3. Grandis mark

DOOR MIRROR

EXTERIOR

51-36

2. Installation procedure

(1) Use 3M ATD Part number 8906 or equivalent

to clean the mark installation surfaces on the
body.

CAUTION

When attaching the marks, the ambient
temperature should be 20

− 38°C and the air

should be completely free of dust. If the ancient
temperature is lower than 20

°C, the marks and

the places on the vehicle body where the marks
are to be attached should be heated to 20

− 38°C.

(2) Peel off the protection sheet on the back of the

marks to paste it on the installation position.

DOOR MIRROR

SERVICE SPECIFICATION

M1511000300455

TROUBLESHOOTING

DIAGNOSIS TROUBLESHOOTING FLOW

M1511014600136

Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points

P.00-5

.

AC302265 AB

16.5 mm

Rear three-diamond mark

Centre line of vehicle

Rear three-diamond mark

Tailgate garnish

AC302288 AB

160 mm

Grandis mark

Grandis mark

Tailgate panel terminal

Application tape

Item

Standard value

Heated door mirror operation current

Ω

7.5

± 1.1

DOOR MIRROR

EXTERIOR

51-37

TROUBLE SYMPTOM CHART

M1511015000148

NOTE: The electric folding door mirrors are
controlled by the Smart Wiring System (SWS). For
troubles relating to the electric folding door mirrors,
refer to GROUP 54B - Troubleshooting

P.54B-74

or

GROUP 54C - Troubleshooting

P.54C-44

.

INSPECTION PROCEDURE 1: All Heated Door Mirrors do not Operate

Symptom

Inspection
procedure

Reference
page

Troubles relating to electric folding door mirrors

-

P.54B-74

All heated door mirrors do not operate

1

P.51-37

The right or left heated door mirror does not operate

2

P.51-39

Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet

REAR WINDOW
DEFOGGER RELAY

REAR WINDOW
DEFOGGER RELAY

DOOR
MIRROR
ASSEMBLY (RH)

DOOR
MIRROR
ASSEMBLY (LH)

MIRROR
HEATER

MIRROR
HEATER

Heated door mirror circuit

DOOR MIRROR

EXTERIOR

51-38

COMMENTS ON TROUBLE SYMPTOM

The heated door mirrors should work for
approximately 11 minutes when the rear defogger
switch is turned on. If the mirror heater does not work
for the specified period, the defogger relay circuit
(heated door mirror power supply circuit) may be
defective.

POSSIBLE CAUSES

• Damaged harness wires and connectors

DIAGNOSIS PROCEDURE

Step 1. Check the rear window defogger.

Check that the rear defogger system should work
normally. (Refer to GROUP 54A, Rear window
defogger inspection

P.54A-176

.)

Q: Is the check result normal?

YES :

Go to Step 2.

NO :

Carry out the troubleshooting for the rear
window defogger. (Refer to GROUP 55,
Troubleshooting

P.55-43

.)

Step 2. Connector check: C-205 junction block
connector.

Q: Is the check result normal?

YES :

The trouble can be an intermittent

malfunction (Refer to GROUP 00, How to
use Troubleshooting/inspection Service
Points

− How to Cope with Intermittent

Malfunction

P.00-5

).

NO :

Repair the defective connector.

AC311691

21

7

16 15

17

18

20 19

1

2

3

4

5

6

23 22

24

25

28

26

27

9

8

10

11

14

12

13

Harness side

AB

Connector: F-205

Junction block (Front view)