Mitsubishi Grandis. Manual — part 834

SERVICE SPECIFICATIONS

AUTOMATIC TRANSMISSION (FF)

23A-3

SERVICE SPECIFICATIONS

M1231000300412

LUBRICANTS

M1231000400475

Item

Standard value

A/T fluid temperature sensor resistance k

Ω

At 0

°C

16.7

− 20.5

At 20

°C

7.3

− 8.9

At 40

°C

3.4

− 4.2

At 60

°C

1.9

− 2.2

At 80

°C

1.0

− 1.2

At 100

°C

0.57

− 0.69

Damper clutch control (DCC) solenoid valve coil resistance (at 20

°C) Ω

2.7

− 3.4

Low & reverse (LR) solenoid valve coil resistance (at 20

°C) Ω

2.7

− 3.4

Second (2ND) solenoid valve coil resistance (at 20

°C) Ω

2.7

− 3.4

Underdrive (UD) solenoid valve coil resistance (at 20

°C) Ω

2.7

− 3.4

Overdrive (OD) solenoid valve coil resistance (at 20

°C) Ω

2.7

− 3.4

Stall speed r/min

2,300

− 2,800

Line pressure MPa

1,01

− 1,05

Item

Specified lubricants

Capacity L

A/T fluid

DIA QUEEN ATF SP III

7.7

SPECIAL TOOL(S)

AUTOMATIC TRANSMISSION (FF)

23A-4

SPECIAL TOOL(S)

M1231000600509

Tools

No.

Name

Application

MB991955

A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991825
F: MB991826

MUT-III sub-assembly

A: Vehicle

Communication
Interface (V.C.I.)

B: MUT-III USB cable
C: MUT-III main

harness A (Vehicles
with CAN
communication
system)

D: MUT-III main

harness B (Vehicles
without CAN
communication
system)

E: MUT-III

measurement
adapter

F: MUT-III trigger

harness

Checking the A/T

CAUTION

For vehicles with CAN
communication, use MUT-III main
harness A to send simulated
vehicle speed. If you connect
MUT-III main harness B instead,
the CAN communication does
not function correctly.

MD991658

Test harness

Voltage measurement

MD998330
(including
MD998331)

Oil pressure gauge (3.0
MPa)

Hydraulic pressure measurement

MB991910

MB991826

MB991955

MB991911

MB991824

MB991827

MB991825

A

B

C

D

E

F

DO NOT USED

MB991658

AC103525

SPECIAL TOOL(S)

AUTOMATIC TRANSMISSION (FF)

23A-5

MD998332

Adapter

Oil pressure gauge connection

MD998900

MB990767

End yoke holder

Fixing of the hub

MB991897

Ball joint remover

Knuckle and tie rod end ball joint
disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113)is also
used to disconnect knuckle and tie
rod end ball joint.

MB990241

A:MB990242
B:MB990244

Axle shaft puller

A: Puller shaft
B: Puller bar

• Drive shaft removal

• Hub assembly removal

A:MB991017
B:MB990998
C:MB991000

A, B: Front hub remover

and installer

C: Spacer

Wheel bearing temporarily fixing
NOTE: Use MB991000 (a part of
MB990998) for spacer

MB991721

Sliding hammer

Output shaft removal

Tools

No.

Name

Application

B990767

AC106827

MB990241AB

A

B

A

B

C

MB991017

SPECIAL TOOL(S)

AUTOMATIC TRANSMISSION (FF)

23A-6

MB991454

Engine hanger balancer When the engine hanger is used:

Supporting the engine assembly
during removal and installation of
the transmission assembly
NOTE: Special tool MB991454 is a
part of engine hanger attachment
set MB991453.

MB991527

Hanger

MB991895

Engine hanger

MB991928

A: MB991929
B: MB991930
C: MB991931
D: MB991932
E: MB991933
F: MB991934

Engine hanger

A: Joint (50)

× 2

B: Joint (90)

× 2

C: Joint (140)

× 2

D: Foot (standard)

× 4

E: Foot (short)

× 2

F: Chain and hook

assembly

Tools

No.

Name

Application

B991454

B991527

Z203830

B991928

A

B

C

D

E

F

Slide bracket (HI)