Mitsubishi Grandis. Manual — part 350
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-19
Step 3. Check the harness wires between key
reminder switch connector C-308 (terminal 7) and
engine-ECU <M/T> or engine-A/T-ECU <A/T>
connector C-112 (terminal 65).
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-20
NOTE: Prior to the wiring harness inspection, check
intermediate connector C-17, and repair if necessary.
Q: Are the harness wires between key reminder
switch connector C-308 (terminal 7) and
engine-ECU <M/T> or engine-A/T-ECU <A/T>
connector C-112 (terminal 65) in good condition?
YES :
Go to Step 4.
NO :
Repair the wiring harness.
Step 4. Check the communication with MUT-III.
Q: Can the system communicate with the MUT-III?
YES :
Go to Step 5.
NO :
Refer to Inspection procedure 1 "Diagnosis
code No.P0513 is set to the MPI system or
the immobilizer ECU cannot communicate
with the MUT-III"
.
Step 5. MUT-III diagnosis code
Check whether the engine immobilizer
system-related diagnosis code is set.
Q: Is the diagnosis code set?
YES :
.
NO :
Go to Step 6.
STEP 6. Check the trouble symptom
Check that the ignition key can be registered.
Q: Is the check result normal?
YES :
The procedure is complete.
NO :
Replace the immobilizer ECU, and then go
to Step 7 .
AC310616
AF
Harness side
Connectors: C-17, C-112 <LHD>
C-112 (GR)
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
C-112
C-17
C-17
AC310629AD
Harness side
Connectors: C-17, C-112 <RHD>
C-112 (GR)
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
C-112
C-17
C-17
AC310153AE
Connector: C-308 <LHD>
Harness side
AC310183
AE
Connector: C-308 <RHD>
Harness side
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-21
STEP 7. Check the trouble symptom
Check that the ignition key can be registered.
Q: Is the check result normal?
YES :
The procedure is complete.
NO :
Replace the engine-ECU <M/T> or
engine-A/T-ECU <A/T>.
Inspection procedure: 3 The engine does not start. (cranking occurs but initial combustion does not)
COMMENTS ON TROUBLE SYMPTOM
If the fuel injection does not work, the immobilizer
ECU and the MPI system may be defective. It is no
problem with the malfunction above when the engine
is started with unregistered ignition key.
POSSIBLE CAUSES
• Malfunction of MPI system
• Malfunction of immobilizer ECU
DIAGNOSIS PROCEDURE
Step 1. Battery voltage check
Measure the battery voltage when cranking.
OK: 8 V or more
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Check the battery. Refer to
.
Step 2. MUT-III other systerm diagnosis code
Check whether the MPI system-related diagnosis
code is set.
Q: Is the diagnosis code set?
YES :
Refer to GROUP 13A
− Troubleshooting
NO :
Go to Step 3.
Step 3. MUT-III diagnosis code
Check whether the engine immobilizer
system-related diagnosis code is set.
Q: Is the diagnosis code set?
YES :
.
NO :
Go to Step 4.
Step 4. Check that the engine starts.
Q: Does the engine start?
YES :
The procedure is complete.
NO :
Refer to GROUP 13, Troubleshooting
. Replace the immobilizer ECU
when the cause of the failure cannot tracked
down by performing the troubleshooting.
Inspection procedure: 4 Check the power supply and earth circuit to the immobilizer ECU.
CIRCUIT OPERATION
Refer to
.
COMMENTS ON TROUBLE SYMPTOM
The power supply and earth circuit to the immobilizer
ECU may be defective.
POSSIBLE CAUSES
• Damaged harness wires and connectors
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-22
DIAGNOSTIC PROCEDURE
Step 1. Connector check: Key reminder switch
connector C-308
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the defective connector.
Step 2. Voltage measurement at key reminder
switch connector C-308 in order to check the
battery circuit of power supply system to the key
reminder switch.
(1) Disconnect the key reminder switch connector
C-308 and measure the voltage at key reminder
switch connector C-308 harness side.
(2) Turn the ignition switch to “ON” position.
(3) Measure the voltage between terminal 5 and
earth.
OK: Battery voltage
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 3.
AC310153AE
Connector: C-308 <LHD>
Harness side
AC310183
AE
Connector: C-308 <RHD>
Harness side
AC310153AE
Connector: C-308 <LHD>
Harness side
AC310183
AE
Connector: C-308 <RHD>
Harness side
AC310507CT
Connector C-308
(Harness side)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст